manualshive.com logo in svg

Lattice Semiconductor ECP5 Versa, Technical Notes, Page: 7 / 78

Share
Download
Lattice Semiconductor ECP5 Versa Technical Notes Download Page 7

7

ECP5 and ECP5-5G Hi

g

h-Speed I/O Interface

Interface Requirements

• The clock input must use a PCLK input so that it can be routed directly to the primary clock tree. 

• The user must set the timing preferences as per section “Timing Analysis Requirement”

GDDRX1_RX.SCLK.Ali

g

ned

This a Generic 1X gearing Receive interface using SCLK. The clock is coming in edge aligned to the Data. This 
interface must be used for speeds below 250 

MHz

.

This DDR interface uses the following modules:

• IDDRX1F element to capture the data

• DDRDLLA/DLLDELD blocks are used to phase shift the incoming clock going to primary clock tree (SCLK) 

• Static data delay element DELAYG is used to delay the incoming data enough to remove the clock injection time. 

• Optionally the user can choose to use Dynamic Data delay adjustment using DELAYF element to control the 

delay on the DATA dynamically. DELAYF will also allow user to override the input delay set. The type of delay 
required can be selected through Clarity Designer

• DEL_MODE attribute is used with DELAYG and DELAYF element to indicate the interface type so that the cor-

rect delay value can be set in the delay element.

• Dynamic Margin adjustment in the DDRDLLA module can be optionally used to adjust the DDRDLLA delay 

dynamically

The output of the DLLDELD module is also used as the clock input to the DDRDLLA which sends the delay values 
to the DLLDELD module. The Receiver Synchronization (RX_SYNC) soft IP is required for the aligned interfaces to 
prevent stability issues that may occur due to this loop at startup. The soft IP will prevent any updates to the DLL-
DELD at start until the DDRDLLA is locked. Once locked the DLLDELD is updated and FREEZE on the DDRDLL is 
removed. This soft IP will be automatically generated by Clarity Designer.

The following figures show the static delay and dynamic delay options for this interface.

Figure 6. GDDRX1_RX.SCLK.Aligned Interface (Static Delay)

IDDRX1F

SCLK

D

Q0

Q1

RST

Datain

Q[0]

Q[1]

Clkin

A

DELAYG

Z

DLLDELD

Z

A

DDRDEL

LOADN
MOVE
DIRECTION
CFLAG

CLK

RST

UDDCNTLN

FREEZE

DDRDEL

LOCK

DDRDLLA

DCNTL[7:0]

“

0

”

“

0

”

(open)

Primary

DEL_MODE =

SCLK_ALIGNED

Ready

STOP

DLL_LOCK

FREEZE

UDDCNTLN

DLL_RESET

DDR_RESET

SYNC_CLK

RST

UPDATE

Sync_clk

Sync_reset

Update

READY

(open)

RX_SYNC

Sclk

Dcntl[7:0]

Summary of Contents for ECP5 Versa















































































Reviews:

No comments