Lattice Semiconductor ECP5 Versa Technical Notes Download | Manualshive

Page: 10 / 78

background image

10

ECP5 and ECP5-5G Hi

g

h-Speed I/O Interface

• DEL_MODE attribute is used with DELAYG and DELAYF element to indicate the interface type so that the cor-

rect delay value can be set in the delay element

• The ECLKBRIDGE can be optionally enabled if the data bus will be crossing over between the left and right sides

of the device. If ECLKBRIDGE is enabled then the ECLKBRIDGECS element should be used in the interface
before the ECLKSYNCB element. This element can be enabled through Clarity Designer.

• Dynamic Margin adjustment in the DDRDLLA module can be optionally used to adjust the DDRDLLA delay

dynamically

The output of the DLLDELD module is also used as the clock input to the DDRDLLA which sends the delay values
to the DLLDELD module. The Receiver Synchronization (RX_SYNC) soft IP is required for the aligned interfaces to
prevent stability issues that may occur due to this loop at startup. The soft IP will prevent any updates to the DLL-
DELD at start until the DDRDLLA is locked. Once locked the DLLDELD is updated and FREEZE on the DDRDLL is
removed. This soft IP will be automatically generated by Clarity Designer.

The following figures show the static delay and dynamic delay options for this interface.

Figure 10. GDDRX2_RX.ECLK.Aligned Interface (Static Delay)

Datain

Clkin

A

DELAYG

Z

DLLDELD

Z

A

DDRDEL

LOADN
MOVE
DIRECTION
CFLAG

CLK

RST

UDDCNTLN

FREEZE

DDRDEL

LOCK

DDRDLLA

DCNTL[7:0]

“ 0”
“ 0”

(open )

ECLKI

STOP

ECLKO

SCLK

D

RST

ALIGNWD

ECLK

Edge

Primary

CLKDIVF

CLKI

RST

ALIGNWD

CDIVX

alignwd

IDDRX2F

Q[3:0]

Q[3:0]

ECLKSYNCB

dcntl[7:0]

STOP

DLL_LOCK

FREEZE

UDDCNTLN

DLL_RESET

DDR_RESET

SYNC_CLK

RST

UPDATE

Sync_clk

sync_reset

Update

READY

Ready

RX_SYNC

DEL_MODE=

ECLK_CENTERED

Sclk

«
...
8
9
10
11
12
...
»

Summary of Contents for ECP5 Versa















































































Reviews:

No comments

Related manuals for ECP5 Versa

Brand: MacDon Pages: 272

Brand: MacDon Pages: 70

Brand: Federal Signal Corporation Pages: 2

Brand: Harman Kardon Pages: 7

Brand: Fellowes Pages: 20

Brand: Gary Machinery Pages: 14

Brand: PASCO Pages: 30

Chicken Coop Plan 3x5

Brand: EASY COOPS Pages: 21

Chicken Coop Plan 4x6

Brand: EASY COOPS Pages: 18

Chicken Coop Plan 8x10

Brand: EASY COOPS Pages: 18

Brand: Hach Pages: 456

Brand: Zennio Pages: 3

TOTAL KNEE 1900

Brand: Össur Pages: 58

mocon AQUATRAN 3/38

Brand: Ametek Pages: 85

INTRAmatic 31 ES

Brand: KaVo Pages: 52

Brand: DAAB Pages: 12

Quadro A Legs 3P 120 Degree Workstation with...

Brand: Jason.L Pages: 10

TRAKTOR KONTROL S3

Brand: Native Instruments Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands