manualshive.com logo in svg

Lathem PC700, User Manual

Share
Download
Lathem PC700 User Manual Download Page 43

 

 

Appendix C - Access Relay Connections  

•

  39 

Appendix C - Access 
Relay Connections 

When you are connecting to a door access device make sure you 
have the following skills: 

•

 

Understand basic wiring principles and techniques 

•

 

Can interpret wiring diagrams 

•

 

Have circuit wiring experience 

Note:

 The wiring must be installed in accordance with national and 

local electrical codes. 

Connecting the PC700 to a Door Strike 

Unplug the relay screw clock connector. 

 

 

 

 

 

 
Connect the wires from the door access device to the screw clocks. 
Plug the clock connector into the socket on the PC700. Only one (1) 
wire should be inserted into the clock block positions NO and COM, 
all wire splices should be done externally. See the following 
diagrams for details. 

 

 

 

 

 

 

 

Important!

 Relay contacts provide no power. The relay is a dry contact 

closure rated 2 amps at 24VDC or 120 VAC. Connecting a door strike 
that draws more than the rated amperage from the clock will result in 
serious damage! It is recommended to use the optional RB8 Relay 
Booster Box for a door strike that requires more than 2 amps. 

Summary of Contents for PC700





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands