manualshive.com logo in svg

Laser Technology Criterion RD 1000, User Manual, Page: 18 / 36

Share
Download
Laser Technology Criterion RD 1000 User Manual Download Page 18

Laser Technology, Inc. Criterion RD 1000 User’s Manual
Page 16

Displaying the Magnification Constant

1. Press the MODE button until the external LCD displays the SYS 

Mode Indicator. 

2. Press the FWD or BACK button until the MAG Status Indicator is 

displayed and “OFF” or “On” appears in the main display.

If “OFF” is displayed, press the UP or DOWN button to toggle 
“ON”.

3. Press and hold the EDIT button for approximately 3 seconds. The 

current Magnification constant appears in the main display. This 
value should match the number that appears on the magnifier.

If you want to use the same Magnification Constant, press the 
MODE button to select a measurement mode.

See below to edit the value of the Magnification Constant.

Press the FWD button to move to the next System Option.

Press the BACK button to move to the previous System Option.

Editing the Value

1. Display the Magnification Constant (see above).
2. Press the EDIT button and use the arrow buttons to edit the value.

Valid Values: 2.00 to 2.99.
a. Press the UP or DOWN button to increase/decrease the 

value.

b. Press the FWD or BACK button to move to next/previous 

digit.

c.

Press the ENTER button to accept the new Magnification 
constant.

Press the MODE button to select a measurement mode.

Press the FWD button to move to the next System Option.

Press the BACK button to move to the previous System Option.

Selecting Measurement Units

The RD 1000 allows you to choose between Metric and Imperial measurement 
units. Refer to the instructions below to toggle the selection.

1. Press the MODE button until the external LCD displays the SYS 

Mode Indicator.

2. Press the FWD or BACK button until the Units Status Indicator and 

distance measurement Unit Indicators (flashing) are displayed.

3. Press the UP or DOWN button to toggle between Imperial and 

Metric Units.

Metric:  M and CM flashing.   Imperial: F and I flashing.

Press the FWD button to move to the next System option.

Press the BACK button to move to the previous System option.

Press the MODE button to select a measurement mode.

Summary of Contents for Criterion RD 1000





































Reviews:

No comments