background image

1

10/21 / V21 / OS-IF / manuals/lc-photon-counter/count-series-user-manual

Single Photon Counting Module 

COUNT

®

-Series User Manual

Table of Contents

Introduction 2
Mounting the Count

®

 modules 

2

 Front-side 

2

 

Base plate 

2

Operation 3
 

Handling single photon counting modules 

3

 

Heat dissipation 

3

 

Gating function and TTL output 

3

 

Optical fiber connection   

 

Electrical connections (rear side) 

4

 

Powering up the module 

4

 

Optimizing performance 

4

Performance 5
 

Spectral response 

5

 

Timing resolution 

5

 

Correction factor 

6

Technical Data 

7

 

Technical specifications for COUNT

®

 module 

7

 

Technical sSpecifications for COUNT

® 

BLUE module 

8

 

Technical specifications for COUNT

® 

NIR module 

9

 

Absolute maximum ratings 

10

 

Interface information 

10

 

Individual module test data 

10

 

ESD information 

10

 Safety 

10

 

RoHS compliance 

10

 Warranty 

10

 

Product number designations 

11

Support 11

3

Detectors

Germany and Other Countries

Laser Components Germany GmbH 
Tel:  +49  8142  2864 – 0 
Fax:  +49  8142  2864 – 11 
[email protected]

www.lasercomponents.com

Summary of Contents for COUNT Series












Reviews: