Larson Davis PRM2103 Reference Manual Download Page 35

Page: 35 / 91

AEC206 Reference Manual

Physical

A-5

A.4 Physical

Reference Direction

0° is perpendicular to plane of microphone diagram,
as shown below

FIGURE A-3

Reference Direction.

Microphone Thread

11.7 mm - 60 UNS (.4606 - 60 UNS)

Diameter

12.7 mm (0.5 in)

Height

132.4 mm (5.25 in)

Weight

64.4 g (2.27 oz.)

Output Connector

10-pin male (FGA. 1B.310)

Venting

377B02 microphone is rear-vented and sealed to the PRM2103 using

an O-ring. The PRM2103 is vented through the 10-pin connector for

pressure equalization.

Microphone Reference

Point

The center of the diaphragm of the 377B02 microphone.

Reference Frequency

1000 Hz

Reference Level

114 dB re. 20



Reference Calibrator

CAL200

Environmental

Operating Temperature

Range

- 40 °C to 70 °C (- 40 °F to 158 °F)

Operating Humidity

Range

0 to 100% relative humidity, excluding internal condensing

Temperature Sensitivity

<±1.0 dB at 1 kHz from -40 °C to -10 °C (-40 °F to 14 °F)

<±0.5 dB at 1 kHz from -10 °C to 50 °C (14 °F to 122 °F)

<±0.9 dB at 1 kHz from 50 °C to 70 °C (122 °F to 158 °F)

Humidity Sensitivity

< ± 0.2 dB @ 1 kHz from 0 to 100% relative humidity, at 40 °C (104 °F)

Summary of Contents for PRM2103




























































































Search results

Summary of Contents for PRM2103

Reviews:

Related manuals for PRM2103

Brands by name

Popular brands

Larson Davis PRM2103, Reference Manual

Search results

Summary of Contents for PRM2103

Reviews:

Related manuals for PRM2103

Brands by name

Popular brands