manualshive.com logo in svg

Larson Davis 831, User Manual

Share
Download
Larson Davis 831 User Manual Download Page 457

A-20

CE Information 

Model 831 Manual

CE Information

Declaration of Conformity

PCB Piezotronics, Inc. declares that:

Model 831 Sound Level Meter

has been measured in representative configuration with: PRM831 preamplifier, 377B02 microphone

and the following cables: EXC010 microphone extension cable, CBL138 USB interface cable and

CBL139 AC/DC output cable with an applied acoustic field of 74 dB at 1 kHz.

Immunity

EN61000-4-2, Level 4
EN61000-4-3, Level 2
EN61000-4-4, Level 2
EN61000-4-5, Level 3
EN61000-4-6, Level 3
EN61000-4-11

Harmonic

EN6100-3-2 (A1 +A2 + A14)

Flicker

EN6100-3-3

Leakage Current

0.20 

A maximum 254 Vac, 54 Hz

Dielectric Withstand (Hipot)

3,000 Vac, 1 minute, 10 mA

MTBF (Full Load, 25



C)



kHrs

AC Input Plugs (supplied)

USA: RPA
Europe: RPE
UK: RPK
Australia: RPS

Dimensions/Weight

Length: 75.32 mm (2.97 in)
Height: 31.67 mm (1.25 in)
Width: 45.96 mm (1.81 in)
Weight: 61.1 g (2.16 oz)

Table A-19  PSA029 AC to DC USB Power Adapter Specifications

Summary of Contents for 831





































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands