manualshive.com logo in svg

Larscom ACST-1500B Series, Installation And Operation Manual, Page: 129 / 340

Share
Download
Larscom ACST-1500B Series Installation And Operation Manual Download Page 129

Note 2:

An Access-T configured as a slave can only

have its

INTERFACE

option set to

TERMINAL

.

9.

Configure the terminal for the same baud rate, data word format, and
handshaking as Access-T. If the terminal is software-configured, save
the configuration so that the correct communications parameters are
the terminal’s start-up defaults. Refer to the terminal manual for
configuration procedures.

10.

Set the modems (if used) for the following, if applicable:

•

Auto answer (S0=1).

•

DTR enabled (&D2).

•

Quiet mode (Q1).

•

DCD enabled

(

&C1

)

.

•

Echo off (E0).

•

Auto Seek command: AT&%C1&%D2&%W
(Hayes 2400 Smartmodem only).

Access-T Operating Modes

Access-T can be configured to operate in one of two modes:

•

Master.

•

Slave.

If Access-Ts are interconnected via their Chain Ports, one must be configured for master
mode and the others must be configured as slaves. The Access-T to which the controlling
terminal or NMS is attached must be configured as the master. If an Access-T 1500
module is to act as the master, you must configure the module in slot 15 as the master.
No other slot position can act as the master. In master mode, Access-T performs various
chain management functions. In slave mode, Access-T responds to the master Access-T,
retaining all software functions except alarm dialout and SNMP communication.

The operation mode for chained Access-Ts must be set locally (as described in Chapter
3) before communication via the Chain Port can occur. When using Access-Ts from
different product groups (detailed in Chapter 1) in the same chain, you must be careful
as to which unit you configure as the master. Table 6-A illustrates the possible
master-slave configuration combinations.

Refer to Chapter 8 for additional information on using Access-T as a master.

Chapter 6

ACST-0351-005

Configuration Procedures

June 1996

6-4

Summary of Contents for ACST-1500B Series





















































































































































































































































































































































Reviews:

No comments