LAPPSET 200202 Installation Manual Download Page 1 | Manualshive

Page: 1 / 20

LAPPSET 200202 Installation Manual Download Page 1

SINGLE MAST NET CLIMBER

MODEL NO.

GS-W1002-1

GSWeb Playground Equipment

1

INSTALLATION MANUAL

Safety Checklist after first assembly

●

Test intervals of Safety: 6 months

●

Test Component and contents:

1. Removing the reticulated system:
- Check of removing condition each rope
- Screwing the turn buckle and conversion the turnbuckle
in anchors plate(see for this workstep turnbuckle assembly)
2. Abrasion condition of rope:
- Checking of all rope surface
- Strengthned of rope: Coating on the surface
3. Attachment condition of the anchors plate and turnbuckle
4. Screwing condition of all bolt
5. Galvanizing condition of the steel component:
- Protection of steel component from corrosion.

●

Measure

In case of the appearance the defect detail is
repaired usually within 3 days after checking.

GSWEB PLAYGROUND EQUIPMENT

1046-3, Najeon-ri, Saengnim-myeon, Gimhae-si
Gyeongsangnam-do, 621-821, Republic Of Korea
Tel) +82. 55. 326. 9096~7
Fax) +82. 55. 326. 9022
E-mail) [email protected]
Web site) www.gsweb21.com

By Lappset Group Oy

200202/ 220202

1
2
3
...
»

Summary of Contents for 200202





















Reviews:

No comments