manualshive.com logo in svg

Lantronix XPress DR, User Manual, Page: 71 / 109

Share
Download
Lantronix XPress DR User Manual Download Page 71

A: Troubleshooting & Technical Support 

 

 XPress™ DR Industrial Device Server User Guide 

71 

Problem/Message  

Reason  

Solution  

The device server appears to be 

set up correctly, but you are not 

communicating with your device 

attached to the device server 

across the network.  

If you are sure that the serial port 

setting is correct, then you may 

not be connecting to the correct 

socket of the device server.  
 

Check the cables and wiring.  

You can check to see whether 

there is a socket connection to or 

from the device server by looking 

at the Ready LED.  
 

If the Ready LED is blinking 

consistently then there is a good 

socket connection.  
 

If the Ready LED is solid green, 

then the socket connection does 

not exist. Use the Connect Mode 

option C0 for making a connection 

to the device server from the 

network. Use Connect Mode 

option C1 or C5 for a connection 

to the network from the device 

server. See the full list of Connect 

Mode Options in the Binary to 

Hexadecimal chapter.  

When connecting to the Web-

Manager within the device server, 

the message “No Connection With 

CoBox” displays.  

Your computer is not able to 

connect to port 30718 (77FEh) on 

the device server.  

Make sure that port 30718 

(77FEh) is not blocked with any 

router that you are using on the 

network. Also make sure that port 

77FEh is not disabled within the 

Security settings of the device 

server.  

Lantronix Technical Support  

Lantronix offers many resources to support our customers and products at 

www.lantronix.com/support

.  For instance, you can ask a question, find firmware downloads, 

access the FTP site and search through tutorials. At this site you can also find FAQs, bulletins, 

warranty information, extended support services and product documentation. 
To contact technical support or sales, look up your local office at 

www.lantronix.com/about/contact.html

.  When you report a problem, please provide the following 

information: 

 

Your name, company name, address, and phone number 

 

Lantronix product and model number 

 

Lantronix MAC address 

 

Firmware version and current configuration 

 

Description of the problem 

 

Status of the unit when the problem occurred (please try to include information on user and 
network activity at the time of the problem). 

When troubleshooting the following problems, make sure that the XPress DR is powered up and 

the Link (L) LED is lit solid green. If the Link LED is not lit, then the physical network connection is 

bad. Confirm that you are using a good network connection.
 

Summary of Contents for XPress DR














































































































Reviews:

No comments