Lantronix x6010 User Manual Download Page 95

Page: 95 / 261

Lantronix

ION x6010 User Guide

33493 Rev. F

https://www.lantronix.com/

Page 95 of 261

Upgrading IONMM and/or NID Firmware – Web Method

The following describes the procedure for upgrading the firmware in the IONMM through the Web

Interface. If the IONMM is to be upgraded at the same time as other modules in the ION Chassis, see

Upgrading Slide-In and Remote Modules

Note

: Doing an IONMM / NID firmware upgrade may cause configuration backup files to be lost.

The steps involved include

. Verify the current IONMM / NID Firmware version,

. Locate the current

IONMM / NID Firmware version,

. Run the TFTP Server, and

, either 1. Upgrade IONMM / NID

Firmware from the

MAIN

tab, or 2. Upgrade IONMM / NID Firmware from the

UPGRADE

tab.

Verify the Current IONMM / NID Firmware Version

Perform this procedure to display the current version of the IONMM firmware via the web interface.

Access the IONMM via the Web interface (see “Starting the Web Interface”).

Select the

MAIN

tab and locate the

Software Revision

area in the

Model Information

section.

(You can also use the

Help

dropdown and select

About ION System Web Interface

to determine

the current firmware version.)

Note the current version of the x6010 NID or IONMM firmware for use in steps D1 and D2

below.

B. Locate and Download the New IONMM / NID Firmware Version

Perform this procedure to locate the IONMM Firmware version via the Web interface.

Go to the Lantronix

Software Upgrades

web page.

Locate the “

Agent Firmware

” section and examine the link in the right hand column (e.g.,

“

Download x6010_1.0.5_AP.bin

”).

Compare the IONMM / NID version displayed in the

MAIN

tab

Software Revision

area with the

version number on the web site, and continue if the web site version is newer than the current

(running) version.

Click the link located in step 1 above to download the new firmware files (e.g.

“C6010_0.6.7_AP.bin” and “C6010_0.6.7_FPGA_AP.bin”).

C. Run TFTP Server

This process requires a TFTP Server to load the new firmware.

Note

: A TFTP Server is not the same as an

FTP server; they use different protocols. You cannot connect to the TFTP Server with an FTP client.

Install, run and configure the TFTP Server.

Copy the file downloaded in step 4 above to the required TFTP Server location.

Note

: the upgrade file must be resident in the default directory on the TFTP server (normally

C:TFTP-Root

Note the location of the downloaded file and its filename for use in steps D1 and D2 below.

Summary of Contents for x6010






































































































































































































































































Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands

Lantronix x6010, User Manual

Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands