Lantronix SLC8 Manager User Manual Download Page 259

Page: 259 / 299

15: Command Reference

SLC™ Console Manager User Guide

259

Description

Sets the acceptable range for the internal temperature sensor (an SNMP trap is sent if the
temperature is outside of this range).

show temperature

Syntax

show temperature

Description

Displays the acceptable range and the current reading from the internal temperature sensor.

USB Commands

set usb access

Syntax

set usb access <enable | disable>

Description

Enables or disables access to USB devices.

set usb modem

Syntax

set usb modem <U1> <parameters>

Parameters

auth <pap|chap>

baud <300-115200>

calleridcmd <Modem Command String>

calleridlogging <enable|disable>

cbcpnocallback <enable|disable>

cbcptype <admin|user>

chapauth <chaphost|localusers>

chaphost <CHAP Host or User Name>

chapsecret <CHAP Secret or User Password>

databits <7|8>

dialbackdelay <PPP Dialback Delay>

dialbacknumber <usernumber|Phone Number>

dialinlist <Host List for Dial-in>

dialoutlogin <User Login>

dialoutnumber <Phone Number>

dialoutpassword <Password>

dodauth <pap|chap>

Summary of Contents for SLC8












































































































































































































































































































Search results

Summary of Contents for SLC8

Reviews:

Related manuals for SLC8

Brands by name

Popular brands

Lantronix SLC8, Manager User Manual

Search results

Summary of Contents for SLC8

Reviews:

Related manuals for SLC8

Brands by name

Popular brands