Lantronix SLC16 User Manual Download | Manualshive

Page: 216 / 351

background image

SLC™ Console Manager User Guide

216

13: Maintenance

The system administrator performs maintenance activities and operates the SLC using the options
for the Maintenance tab and additional commands on the command line interface.

SLC Maintenance

The

Maintenance > Firmware & Config

page allows the system administrator to:



Configure the FTP, SFTP, or TFTP server that will be used to provide firmware updates and
save/restore configurations. (TFTP is only used for firmware updates.)



Set up the location or method that will be used to save or restore configurations (default, FTP,
SFTP, NFS, CIFS, PC card, or USB). Update the version of the firmware running on the SLC
console manager .



Save a snapshot of all settings on the SLC unit (save a configuration).



Restore the configuration, either to a previously saved configuration, or to the factory defaults.



View and terminate current web sessions.



View the firmware version on each boot bank, select the bank to boot from, and copy the
contents of one boot bank to the other.

To configure settings:

1.

Click the

Maintenance

tab. The

Maintenance > Firmware & Config

page displays.

«
...
214
215
216
217
218
...
»

Summary of Contents for SLC16
































































































































































































































































































































































Reviews:

No comments

Related manuals for SLC16

AirPlus DWL-810

Brand: D-Link Pages: 25

Brand: H3C Pages: 1057

System x3630 M4

Brand: IBM Pages: 7

Brand: Paradyne Pages: 16

Brand: 3Com Pages: 8

8 Port 10/100Mbit/s Ethernet Smart Switch with Fibre Uplink

Brand: Tyco Electronics Pages: 18

Brand: Patton electronics Pages: 2

Brand: Patton electronics Pages: 86

Brand: Quantum Pages: 20

Firebox SOHO 6 Wireless

Brand: Watchguard Pages: 8

SRCSASBB8I - RAID Controller

Brand: Intel Pages: 36

Emulator MCU Board for 38D5 Group M38D59T-RLFS

Brand: Renesas Pages: 4

Brand: Garland Pages: 43

LBON320AC Series

Brand: Lindsay Broadband Pages: 4

Speed Touch 591s

Brand: Alcatel Pages: 184

Brand: IFM Electronic Pages: 14

Brand: JLCooper Electronics Pages: 12

Brand: Handicare Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands