manualshive.com logo in svg

Lantronix SISTP10 0-3-LRT Series, Install Manual, Page: 17 / 31

Share
Download
Lantronix SISTP10 0-3-LRT Series Install Manual Download Page 17

Lantronix 

 

SISTP10x0-3xx-LRT Install Guide

   

33733 Rev. G 

                  

https://www.lantronix.com/

   

Page 

17

  of 

31

 

Power Supply Features and Specifications

 

The Industrial Power Supplies (25104 and 25105) are optional accessories (sold separately).   

•

 

25104 Input: 85-264 VAC, 124-370 VDC.    Output: 48~55 VDC, 5.0A, 240 Watts. 

•

 

25105 Input: 85-264 VAC, 124-370 VDC.  Output: 48~55 VDC, 2.5A, 120 Watts. 

Industrial Power Supply 25105

 

Output   

Output Voltage   

48VDC   

Current Rating    

2.5A   

Power Rating     

120 Watts   

Ripple & Noise Max    120mVp-p   
Voltage Range    

48~55VDC   

Voltage Tolerance 

±1.0%   

Line Regulation  

  ±0.5%   

Load Regulation   

±1.0%   

Setup, Rise Time   

1500ms, 60ms   

Hold Up Time     

20ms   

Input   

Voltage Range    

Switch Selectable 88~264VAC 124~370VDC   

Frequency Range   

47~63Hz   

Efficiency   

 

90.5%   

AC Current (Typical)    1.4A@115VAC 0.7A@230VAC   
Inrush Current (Cold)    35A@115VAC 70A@230VAC Leakage Current <1.0mA@240VAC   

Protection   

Overload   

 

110~150%   

Overvoltage     

56~65V   

Over Temperature   

95ºC±5ºC   

Environment   

Operating Temp.   

-25ºC~+70ºC. Storage Temp. -40ºC~+85ºC. Operating Humidity: 20~95% non-condensing.   

Features 

91% High Efficiency.    150% Peak Load.   
Protected against:   

Short Circuit, Overload, Over Voltage, Overheating.   

Convection air cooling.  DIN rail mountable. RoHS compliant. MTBF 298.9 Khrs.   
Dimensions (mm):   

40W, 125.2H, 113.5D.    Weight .67Kg. 

Standards 

Safety: UL508, TUV EN60950-1. Vibration: IEC60068-2-6 
EMC Emission: EN55011, EN55022, CISPR22 Class B, EN61000-3-2, |EN61000-3-3. 
EMC Immunity: EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-8, EN61000-4-
11, EN55024, EN61000-6-2, EN50082-2, EN61204-3, SEMI F47, GL Approved. 

Note

: 

Both the switch and the power supply must have their ground terminals connected to earth ground.

   

Summary of Contents for SISTP10 0-3-LRT Series
































Reviews:

No comments