manualshive.com logo in svg

Lantronix SISGM1040-284-LRT, Install Manual, Page: 36 / 45

Share
Download
Lantronix SISGM1040-284-LRT Install Manual Download Page 36

Lantronix 

 

SISGM1040-284-LRT Install Guide

 

33808 Rev. E 

                   

https://www.lantronix.com/

   

36 

Connecting Power 

ATTENTION

 

This case must be earth grounded. No DC input may be earth grounded. Use Isolated Power Supply. 

The switch can be powered from two power supplies (input range 12V ~ 58V).   

Insert the positive and negative wires into 

P1+

 and 

P1-

 contacts on the terminal block and tighten the wireclamp 

screws to prevent the wires from being loosened. If redundant power supplies are to be configured, insert the 

positive and negative wires into P2+ and P2- contacts on the terminal block and tighten the wireclamp screws. 

Note

: See “

Power Supply Warnings & Cautions !!

”, “

Power Supply Installation

”, and “

Power Supply Mounting 

Instructions

” later in this manual for detailed information. 

Note

: Make all cable connections before connecting Power. 

Power Connector (4-Pin Terminal Block) 
Input

:    

DC 12-58V 

P1 +/- 

  

Power Input 1 + and - 

P2 +/- 

  

Power Input 2 + and - 

ALM 

   

Alarm Relay Output 

Note

: The DC power should be connected to a well-fused power supply. 

Note

: 

See “

Power Supply Warnings & Cautions !!”,

 

“Power Supply Installation

”, and “

Power Supply Mounting 

Instructions

” later in this manual for detailed information. 

Summary of Contents for SISGM1040-284-LRT














































Reviews:

No comments