manualshive.com logo in svg

Lantronix SISGM1040-284-LRT, Install Manual, Page: 26 / 45

Share
Download
Lantronix SISGM1040-284-LRT Install Manual Download Page 26

Lantronix 

 

SISGM1040-284-LRT Install Guide

 

33808 Rev. E 

                   

https://www.lantronix.com/

   

26 

Ground Screw 

The front panel provides a ground screw. After the Switch is mounted and connected, the 

front panel grounding screw can be used for grounding. Grounding and wire routing help 

limit the effects of noise due to electromagnetic interference (EMI). Run the ground 

connection from the ground screw to the grounding surface before connecting devices. 

ATTENTION

: 

This case must be earth grounded. No DC input may be earth grounded.   

Use Isolated Power Supply.   

 

RESET Button   

The system Reset button is provided to reboot the system without the need to remove power. 

Under normal circumstances, you will not have to use it. However, on rare occasions, the switch 

may not respond, and you may need to push the Reset button. 

 

Console Port 

The Console port is for local management by using a terminal emulator or a computer with terminal 

emulation software. 

•

 

DB9 connector connect to PC COM port 

•

 

Baud rate: 115200bps 

•

 

8 Data bits, 1 Stop bit 

•

 

Priority: None 

•

 

Flow control: None 

To connect the host PC to the console port, an RJ45 (male) connector-to-RS232 DB9 (female) 

connector cable is required. The RJ45 connector of the cable is connected to the Console port of the SISGM1040-

384D-LRT. The DB9 connector of the cable is connected to the PC COM port. The console cable pin assignments 

are shown below: 

 

 

 

Summary of Contents for SISGM1040-284-LRT














































Reviews:

No comments