manualshive.com logo in svg

Lantronix SISGM1040-284-LRT, Install Manual, Page: 15 / 45

Share
Download
Lantronix SISGM1040-284-LRT Install Manual Download Page 15

Lantronix 

 

SISGM1040-284-LRT Install Guide

 

33808 Rev. E 

                   

https://www.lantronix.com/

   

15 

LED Descriptions 

The front panel LEDs provide switch status as follows: 

Power LEDs (P1 and P2)

: indicate whether the switch is powered up correctly. 

SYS (System) LED

: indicates if the system is ready or not. 

ALM (Alarm) LED

: indicates if the system is operating normally.   

RM (Ring Master) LED

: indicates if Ring Master(s) or Slave is enabled.

 

RC (Rapid Chain) LED

: indicates the status of the Rapid-Chain.

 

Port Status LEDs

: indicate the current status of each port. Check these LEDs to 

determine the port status. 

The following tables details the functions and descriptions of these LED indicators. 

Table 1: Power LEDs 

LED   

Color 

State 

Description 

P1

 

(Power1) 

Green 

On 

The switch is powered ON correctly. 

Off 

The switch is not receiving power from power1. 

P2

   

(Power2) 

Green 

On 

The switch is powered ON correctly. 

Off 

The switch is not receiving power from power2. 

Table 2: System LED 

LED   

Color 

State 

Description 

SYS

 

(System) 

Green 

On 

The switch is ready. 

Off 

The switch is not ready. 

Table 3: Alarm LED 

LED 

Color 

State 

Description 

ALM

 

(Alarm) 

Red 

On 

An abnormal state, such as temperature, voltage, or DC 

power1/2 was detected in the switch. 

Off 

The system is normal. 

 
 

 

Summary of Contents for SISGM1040-284-LRT














































Reviews:

No comments