Lantronix SISGM1040-284-LRT Install Manual Download Page 14 | Manualshive

Page: 14 / 45

Lantronix SISGM1040-284-LRT Install Manual Download Page 14

Lantronix

SISGM1040-284-LRT Install Guide

33808 Rev. E

https://www.lantronix.com/

14

Related Manuals

SISGM1040-284-LRT Quick Start Guide, 33807

SISGM1040-284-LRT Web User Guide, 33809

SISGM1040-284-LRT CLI Reference, 33810

SISGM1040-284-LRT API User Guide, 33827

Power Supply manuals (model specific)

Release Notes (version specific)
For Lantronix Documentation, Firmware, App Notes, etc. go to

https://www.lantronix.com/technical-support/

Note that this manual provides links to third party web sites for which Lantronix is not responsible.

Laser Safety Instructions

When a connector is removed during installation, testing, or servicing, or when an energized fiber is broken, a risk

of ocular exposure to optical energy that may be potentially hazardous occurs, depending on the laser output

power. The primary hazards of exposure to laser radiation from an optical-fiber communication system are:

•

Damage to the eye by accidental exposure to a beam emitted by a laser source.

•

Damage to the eye from viewing a connector attached to a broken fiber or an energized fiber.

Front Panel

The switch front panel provides all the connections, controls and LED indicators as shown and described below.

«
...
12
13
14
15
16
...
»

Summary of Contents for SISGM1040-284-LRT














































Reviews:

No comments