Lantronix PremierWave 2050 Command Reference Manual Download Page 79

Page: 79 / 428

5: Commands and Levels

PremierWave® 2050 Enterprise Wi-Fi® IoT Module Command Reference

default mode

Restores the AP mode to the default value (Always Up).

default suite

Restores the security method (suite) to the default value
(None).

dns redirect

<text>

Set the DNS redirect. <text> = Hostname.

exit

Returns to the config level.

first client connect timeout

<seconds>

Sets the First Client Connect Timeout for SoftAP trigger
mode in seconds.

ip address

<ip address/cidr>

Sets the IP address of Access Point. Formats accepted:
192.168.1.1 (default mask) 192.168.1.1/24 (CIDR)
"192.168.1.1 255.255.255.0" (explicit mask)

last client disconnect timeout

<seconds>

Sets the Last Client Disconnect Timeout for SoftAP trigger
mode in seconds.

mode always up

Sets the AP mode to Always Up.

mode triggered

Sets the AP mode to Triggered.

multicast forwarding disable

Disables Multicast Forwarding.

multicast forwarding enable

Enables Multicast Forwarding.

network name

<text>

Set Network Name (SSID). <text> = Network
Name(SSID).

no dns redirect

Clears the DNS redirect.

no network name

Clears Network Name (SSID).

no passphrase

Clears the password.

passphrase

<text>

Sets the value for the password. <text> = put quotes
around the characters (max 63).

show

Displays the current configuration.

show history

Displays the last 20 commands entered during the current
CLI session.

show status

Displays statistics.

ssid broadcast disable

Disables SSID Broacast.

ssid broadcast enable

Enables SSID Broadcast.

state disable

Disables Access Point.

state enable

Enables Access Point.

suite none

Sets the security suite to None.

suite wpa

Sets the security suite to WPA.

suite wpa2

Sets the security suite to WPA2.

trigger ap

Triggers soft AP.

write

Stores the current configuration in permanent memory.

action (config-action-select) level commands

clrscrn

Clears the screen.

eth0 link state change

Enters the eth0 link state change alarm level.

exit

Exits to the config level.

on scheduled reboot

Enters the on scheduled reboot alarm level.

show history

Displays the last 20 commands entered during the current
CLI session.

usb0 link state change

Enters the usb0 link state change alarm level.

wlan0 link state change

Enters the wlan0 link state change alarm level.

write

Stores the current configuration in permanent memory.

Summary of Contents for PremierWave 2050













































































































































































































































































































































































































































Search results

Summary of Contents for PremierWave 2050

Reviews:

Related manuals for PremierWave 2050

Brands by name

Popular brands

Lantronix PremierWave 2050, Command Reference Manual

Search results

Summary of Contents for PremierWave 2050

Reviews:

Related manuals for PremierWave 2050

Brands by name

Popular brands