Lantronix PremierWave 2050 Command Reference Manual Download Page 341

Page: 341 / 428

5: Commands and Levels

PremierWave® 2050 Enterprise Wi-Fi® IoT Module Command Reference

341

write

Stores the current configuration in permanent memory.

http post (config-action-http_post:usb0 link state change) level commands

clrscrn

Clears the screen.

connection

<instance>

Enters the next lower level. Specify the instance for the
next lower level.

default mode

Sets default of simultaneous connection mode.

exit

Exits to the next higher level.

mode sequential

Sets sequential mode; will stop after first connection that
goes through.

mode simultaneous

Sets simultaneous mode; will make all possible connec-
tions.

no reminder interval

Clears the HTTP Post reminder interval. HTTP Post is
sent once only.

reminder interval

<minutes>

Sets the HTTP Post reminder interval.

show

Shows the current configuration.

show history

Displays the last 20 commands entered during the current
CLI session.

write

Stores the current configuration in permanent memory.

http post (config-action-http_post:on scheduled reboot) level commands

clrscrn

Clears the screen.

connection

<instance>

Enters the next lower level. Specify the instance for the
next lower level.

default mode

Sets default of simultaneous connection mode.

exit

Exits to the next higher level.

mode sequential

Sets sequential mode; will stop after first connection that
goes through.

mode simultaneous

Sets simultaneous mode; will make all possible connec-
tions.

no reminder interval

Clears the HTTP Post reminder interval. HTTP Post is
sent once only.

reminder interval

<minutes>

Sets the HTTP Post reminder interval.

show

Shows the current configuration.

show history

Displays the last 20 commands entered during the current
CLI session.

write

Stores the current configuration in permanent memory.

http post (config-action-http_post:eth0 link state change) level commands

clrscrn

Clears the screen.

connection

<instance>

Enters the next lower level. Specify the instance for the
next lower level.

default mode

Sets default of simultaneous connection mode.

exit

Exits to the next higher level.

mode sequential

Sets sequential mode; will stop after first connection that
goes through.

mode simultaneous

Sets simultaneous mode; will make all possible connec-
tions.

no reminder interval

Clears the HTTP Post reminder interval. HTTP Post is
sent once only.

Summary of Contents for PremierWave 2050













































































































































































































































































































































































































































Search results

Summary of Contents for PremierWave 2050

Reviews:

Related manuals for PremierWave 2050

Brands by name

Popular brands

Lantronix PremierWave 2050, Command Reference Manual

Search results

Summary of Contents for PremierWave 2050

Reviews:

Related manuals for PremierWave 2050

Brands by name

Popular brands