Lantronix PremierWave 2050 Command Reference Manual Download Page 126 | Manualshive

Page: 126 / 428

background image

5: Commands and Levels

PremierWave® 2050 Enterprise Wi-Fi® IoT Module Command Reference

126

show sessions

Show active Telnet and SSH Sessions

ssh

Enters the SSH configuration level.

ssh

<optClientUsername>

<host>

Begin SSH session on network <host>. The optClien-
tUserName must match an SSH Client: Users configura-
tion entry. Use "" in optClientUserName to prompt for host
username and password.

ssh

<optClientUsername>

<host>

<port>

Begin SSH session on network <host>:<port>. The
optClientUserName must match an SSH Client: Users
configuration entry. Use "" in optClientUserName to
prompt for host username and password.

ssl

Enters the SSL configuration level.

tcpdump

<parameters>

dump traffic on a network

telnet

<host>

Begin telnet session on network <host>.

telnet

<host>

<port>

Begin telnet session on network <host>:<port>.

trace route

<host>

Trace route to destination

trace route

<host>

<protocol>

Trace route to destination using TCP, ICMP, or UDP

tunnel

<line>

Enters the tunnel level. <line> = number of the tunnel line
(serial port) to be configured.

usb

<line>

Enters the usb level. <line> = number of the line (usb port)
to be configured.

write

Stores the current configuration in permanent memory.

xml

Enters the XML level.

eth0 link state change (config-action:eth0 link state change) level commands

clrscrn

Clears the screen.

default delay

Resets alarm processing delay to its default value.

delay

<seconds>

Sets the delay in processing the alarm. Alarm actions will
not be executed if the cause is corrected within this time.

email

Enters the next lower level.

exit

Exits to the config alarm level.

ftp put

Enters the next lower level.

http post

Enters the next lower level.

show

Displays the current configuration.

show history

Displays the last 20 commands entered during the current
CLI session.

show status

Displays statistics.

snmp trap

Enters the next lower level.

write

Stores the current configuration in permanent memory.

failover (config-ethernet-failover:usb0) level commands

clrscrn

Clears the screen.

default failback threshold

Restores the default Failback threshold.

default failover interface

Restores the default Failover interface.

default failover threshold

Restores the default Failover threshold.

default interval

Restores the default Ping interval.

default method

Restores the default ping method.

default timeout

Restores the default Ping response timeout.

exit

Exit back to interface configuration level

«
...
124
125
126
127
128
...
»

Summary of Contents for PremierWave 2050













































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PremierWave 2050

Brand: Echelon Pages: 40

Brand: LAE electronic Pages: 7

Brand: LAE electronic Pages: 2

Compact Comfort VAV12

Brand: SAI HVAC Pages: 16

Brand: saia-burgess Pages: 203

Brand: Sailor Pages: 1

Brand: Velleman Pages: 26

Brand: Velleman Pages: 32

Brand: Velocity Pages: 84

Brand: Fingertips Lab Pages: 15

Brand: JASTEC Pages: 18

Brand: HomeMatic Pages: 36

Brand: Kohler Pages: 48

AUTOPULSE IQ-318

Brand: Notifier Pages: 62

Brand: Gecko Pages: 82

Brand: Z-Wave Pages: 44

HydroGuard 1430 Series

Brand: Powers Pages: 8

Brand: Watt Stopper Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands