background image

 

The information in this guide may change without notice. The manufacturer 
assumes no responsibility for any errors which may appear in this guide.

DEC, thickwire, thinwire, and VMS are trademarks of Digital Equipment 
Corporation. UNIX is a registered trademark of AT&T. Ethernet is a trademark of 
XEROX Corporation. HP-UX is a trademark of Hewlett-Packard Corporation. 
SunOS and Solaris are trademarks of Sun Microsystems, Inc. NetWare is a 
trademark of Novell Corp. Windows NT and Windows 95 are trademarks of 
Microsoft Corporation. 

Copyright 1998, Lantronix. All rights reserved. No part of the contents of this book 
may be transmitted or reproduced in any form or by any means without the 
written permission of Lantronix. Printed in the United States of America.

The revision date for this manual is

 

 October 7, 1998

 

.

 

Part Number: 900-148

 

Rev. A

WARNING

This equipment has been tested and found to comply with the limits for a Class A 
digital device pursuant to Part 15 of FCC Rules. These limits are designed to 
provide reasonable protection against such interference when operating in a 
commercial environment. This equipment generates, uses, and can radiate radio 
frequency energy, and if not installed and used in accordance with this guide, may 
cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause interference in 
which case the user, at his or her own expense, will be required to take whatever 
measures may be required to correct the interference. 

Warning: Changes or modiÞcations to this device not explicitly approved by 
Lantronix will void the user's authority to operate this device.

Cet appareil doit se soumettre avec la section 15 des statuts et r•glements de FCC. 
Le fonctionnement est subjectŽ aux conditions suivantes:

(1) Cet appareil ne doit pas causer une interfŽrence malfaisante.

(2) Cet appareil do”t accepter n'importŽ quelle interfŽrence re“ue qui peut causer 
une opŽration indŽsirable.

Summary of Contents for MSS1-T





















Reviews: