background image

 

 

5:  Installation 

E210 Series Cellular Router User Guide 

 

21 

5.6.6  Default Configuration 

All usernames and passwords are case sensitive. 

5.6.6.1  Default Configuration for Web Admin Page 

If the installed ePack firmware is version 2.4.4 and higher, the default factory passwords are:  

User

 

Default Password

 

admin 

admin 

root 

L@ntr0n1x 

Table 5-3: Default Web Admin Page Credentials 

Note:  

 

ePack firmware versions 2.4.4 and above require you to change the factory default 

passwords before any other router configuration can be done. Both the admin and 

root passwords must be changed.  

If the installed ePack firmware is older than version 2.4.4, the default factory passwords are:  

User

 

Default Password

 

admin 

admin 

root 

M@estroW1rele$$ 

Table 5-4: Default Web Admin Page Credentials 

Note: Username and password are both case sensitive. 

 

5.6.6.2  Wireless Access Point SSID 

The wireless access point SSID may be configured in the Web Admin console. 

Parameter

 

Details

 

SSID 

Lantronix E21X - for E210 series devices 
Lantronix E22X - for E220 series devices  

WPA/WPA2 TKIP Key 

W1rele$$ 

Table 5-5: Default Wi-Fi Credentials  

 

5.6.6.3  Default Interface Configuration 

Interface 

Details 

WAN (Ethernet) 

Automatic (DHCP client) 
Priority source of Internet with Cellular backup 

LAN (Ethernet) 

Active DHCP with starting IP address 

192.168.1.100 with pool of 100 clients. 

Cellular 

No PAP/CHAP authentication 

Wireless (LAN) 

Wi-Fi enabled as access point with SSID 

"Lantronix E21X" or "Lantronix E22X" 

Table 5-6: Default Interface Configuration 

Summary of Contents for Maestro E214
























Reviews: