manualshive.com logo in svg

Lantronix EDS-MD Series, Command Reference Manual


Share
Download
background image

5:  Commands and Levels 

EDS-MD® Wired IoT Device Gateway Command Reference 

712 

 

no gateway 

Clears the gateway for static route network. 

no interface 

Clears the route interface. The WAN interface is 
used if no interface is specified. 

no network 

Clears the IP address for static route network. 

show 

Displays the current configuration. 

show history 

Displays the last 20 commands entered during the 
current CLI session. 

state disable 

Disables the static route. 

state enable 

Enables the static route. 

static route 

<number>

 

Change to config gateway static route level. 

write 

Stores the current configuration in permanent 
memory. 

static route 6 (config-staticroute:6) level commands 

clrscrn 

Clears the screen. 

default metric 

Restores the metric to default value. 

exit 

Exits to the config-gateway level. 

friendly name 

<text>

 

Set the friendly name for static route. <text> = 
friendly name 

gateway 

<text>

 

Sets the gateway for static route network. 

interface 

<text>

 

Sets the route interface <text> = interface name 

metric 

<number>

 

Sets the metric for static route. <number> = metric 

network 

<text>

 

Sets the IP address and network mask for static 
route network. 

no friendly name 

Remove the friendly name 

no gateway 

Clears the gateway for static route network. 

no interface 

Clears the route interface. The WAN interface is 
used if no interface is specified. 

no network 

Clears the IP address for static route network. 

show 

Displays the current configuration. 

show history 

Displays the last 20 commands entered during the 
current CLI session. 

state disable 

Disables the static route. 

state enable 

Enables the static route. 

static route 

<number>

 

Change to config gateway static route level. 

write 

Stores the current configuration in permanent 
memory. 

static route 7 (config-staticroute:7) level commands 

clrscrn 

Clears the screen. 

default metric 

Restores the metric to default value. 

exit 

Exits to the config-gateway level. 

friendly name 

<text>

 

Set the friendly name for static route. <text> = 
friendly name 

gateway 

<text>

 

Sets the gateway for static route network. 

interface 

<text>

 

Sets the route interface <text> = interface name 

metric 

<number>

 

Sets the metric for static route. <number> = metric 

network 

<text>

 

Sets the IP address and network mask for static 
route network. 

no friendly name 

Remove the friendly name 

Summary of Contents for EDS-MD Series



































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EDS-MD Series

Lantronix PremierWave 2050 User Manual preview
PremierWave 2050
Brand: Lantronix Pages: 73
Lantronix EMG 8500 Quick Start Manual preview
EMG 8500
Brand: Lantronix Pages: 2
Linksys SPA400 Administration And Configuration Manual preview
SPA400
Brand: Linksys Pages: 13
3onedata GW110X Series User Manual preview
GW110X Series
Brand: 3onedata Pages: 44
MARCOM GW-DLMS-485-ELSA15 User Manual preview
GW-DLMS-485-ELSA15
Brand: MARCOM Pages: 13
Doepke DCI 4 DALI Installation And Operating Manual preview
DCI 4 DALI
Brand: Doepke Pages: 44
Raymarine MICRO-TALK Installation Instructions Manual preview
MICRO-TALK
Brand: Raymarine Pages: 84
Inteno DG201 R1 Installation Manual preview
DG201 R1
Brand: Inteno Pages: 10
Veratron B00042201 Operating Instructions Manual preview
B00042201
Brand: Veratron Pages: 79
Fanvil PA2S User Manual preview
PA2S
Brand: Fanvil Pages: 71
Geneko GWG User Manual preview
GWG
Brand: Geneko Pages: 158
Huawei HA35 User Manual preview
HA35
Brand: Huawei Pages: 92
Huawei HG622 User Manual preview
HG622
Brand: Huawei Pages: 29
Huawei EchoLife HG8240 Service Manual preview
EchoLife HG8240
Brand: Huawei Pages: 358
Huawei EchoLife HG553 User Manual preview
EchoLife HG553
Brand: Huawei Pages: 57
Huawei HG256 User Manual preview
HG256
Brand: Huawei Pages: 42
Huawei EchoLife HG8045A Product Description preview
EchoLife HG8045A
Brand: Huawei Pages: 42
Huawei B686 Manual preview
B686
Brand: Huawei Pages: 63

Brands by name

Popular brands

Load more brands