manualshive.com logo in svg

Lantronix EDS-MD Series, Command Reference Manual


Share
Download
background image

5:  Commands and Levels 

EDS-MD® Wired IoT Device Gateway Command Reference 

671 

 

verbose response enable 

Sends Modem Response Codes out on the Serial 
Line. 

write 

Stores the current configuration in permanent 
memory. 

modem (tunnel-modem:7) level commands 

clrscrn 

Clears the screen. 

connect string 

<text>

 

Sets the CONNECT string used in modem 
emulation. <string> = connect string. 

default incoming connection 

Default disables incoming network connections. 

default response type 

Default uses text type responses. 

display remote ip disable 

The incoming RING has nothing following it. 

display remote ip enable 

The incoming RING is followed by the IP address of 
the caller. 

echo commands disable 

Does not echo modem commands. 

echo commands enable 

Echoes modem commands. 

echo pluses disable 

Does not echo the +++ characters when entering 
modem command mode. 

echo pluses enable 

Echoes the +++ characters when entering modem 
command mode. 

error unknown commands disable 

Returns OK on unknown AT commands. 

error unknown commands enable 

Returns an error upon unknown AT commands. 

exit 

Returns to the tunnel level. 

incoming connection automatic 

Automatically answer incoming network 
connections. 

incoming connection disabled 

Disable incoming network connections. 

incoming connection manual 

Wait for an ATA command before answering an 
incoming network connection. 

no connect string 

Removes optional CONNECT string information for 
modem emulation. 

reassert 

Asserts tunnel modem status with current 
configured values. 

response type numeric 

Uses numeric type responses. 

response type text 

Uses text type responses. 

show 

Displays the current configuration. 

show history 

Displays the last 20 commands entered during the 
current CLI session. 

show status 

Displays tunnel modem status. 

verbose response disable 

Does not send Modem Response Codes. 

verbose response enable 

Sends Modem Response Codes out on the Serial 
Line. 

write 

Stores the current configuration in permanent 
memory. 

modem (tunnel-modem:6) level commands 

clrscrn 

Clears the screen. 

connect string 

<text>

 

Sets the CONNECT string used in modem 
emulation. <string> = connect string. 

default incoming connection 

Default disables incoming network connections. 

default response type 

Default uses text type responses. 

display remote ip disable 

The incoming RING has nothing following it. 

Summary of Contents for EDS-MD Series



































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EDS-MD Series

Patton 1000 Getting Started Manual preview
1000
Brand: Patton Pages: 181
2N EasyGate IP Quick Manual preview
EasyGate IP
Brand: 2N Pages: 2
2N EasyGate Quick Start preview
EasyGate
Brand: 2N Pages: 2
2N stargate Quick Manual preview
stargate
Brand: 2N Pages: 4
SMC Networks EliteConnect SMCWHSG14-G Specifications preview
EliteConnect SMCWHSG14-G
Brand: SMC Networks Pages: 2
Abocom HA2500 Specification Sheet preview
HA2500
Brand: Abocom Pages: 2
Pathport PWPP DIN P4 Manual preview
PWPP DIN P4
Brand: Pathport Pages: 3
Gree ME30-24/E6 Service Manual preview
ME30-24/E6
Brand: Gree Pages: 21
Cisco Meraki Z3 Installation Manual preview
Meraki Z3
Brand: Cisco Pages: 10
Cisco MERAKI MR66 Manual preview
MERAKI MR66
Brand: Cisco Pages: 7
Cisco MERAKI MR66 Installation Manual preview
MERAKI MR66
Brand: Cisco Pages: 19
Cisco Network Device MGX 8240 Task List preview
Network Device MGX 8240
Brand: Cisco Pages: 2
Cisco Physical Access CIAC-GW-K9 Installing And Configuring preview
Physical Access CIAC-GW-K9
Brand: Cisco Pages: 26
Cisco VG350 Installation Manual preview
VG350
Brand: Cisco Pages: 60
Cisco RF Gateway 10 Release Notes preview
RF Gateway 10
Brand: Cisco Pages: 58
Cisco Linksys WPG12 User Manual preview
Linksys WPG12
Brand: Cisco Pages: 29
Cisco WAG54G User Manual preview
WAG54G
Brand: Cisco Pages: 94
Cisco RF 1 Specifications preview
RF 1
Brand: Cisco Pages: 5

Brands by name

Popular brands

Load more brands