background image

 

 

 
 

 

 

 

EXPLORER 40 

 

WARNING!  THIS IS NOT A TOY! 

 

THIS IS NOT A BEGINNERS AIRPLANE 

 

This R/C kit and the model you will build from it is not a toy!  It is capable of 
serious bodily harm and property damage. It is your responsibility, and yours 
alone - 

to build this kit correctly, properly install all R/C. components and flying gear 

(engine, tank, radio, pushrods, etc. and to test the model and fly it only with 
experienced, competent help, using common sense and in accordance with all safety 
standards as set forth in the Academy of Model Aeronautics Safety Code.  It is 
suggested that you join the AMA and become properly insured before attempting to 
fly this model.  If you are just starting R/C modeling, consult your local hobby dealer 
or write to the Academy of Model Aeronautics to find an experienced instructor in 
your area.                                                                                                                                        

Write to : Academy of Model Aeronautics, 5151 Memorial Dr, Muncie, IN 47302 

 

 

LIMITED WARRANTY 

 

Lanier R/C is proud of the care and attention that goes into the manufacture of parts for its 
model kits.  The company warrants that for a period of 

3

0 days, it will replace, at the buyers 

request, any parts or material shown to the company's satisfaction to have been defective in 
workmanship or material at the time of purchase. 
 
No other warranty of any kind, expressed or implied, is made with respect to the 
merchandise sold by the company.  The buyer acknowledges and understands that he is 
purchasing only a component kit from which the buyer will himself construct a finished flying 
model airplane.  The company is neither the manufacturer of such a flying model airplane, 
nor a seller of it.  The buyer hereby assumes the risk and all liability for personal or property 
damage or injury arising out of the buyers use of the components or the finished flying model 
airplane, whenever any such damage or injury shall occur. 

      
         
 

Summary of Contents for EXPLORER 40
























Reviews: