Bench
options
ASSEMBLE
WITH
CARE!
Pangard II
Polyester
Powder
coat
is
a
strong,
long
‐
lasting
finish.
To
protect
this
finish
during
assembly,
place
unwrapped
powder
coated
parts
on
packaging
foam
or
other
non
‐
marring
surface.
Do
not
place
or
slide
powder
coated
parts
on
concrete
or
other
hard
or
textured
surface
– this
will
damage
the
finish
causing
rust
to
occur.
Use
touch
‐
up
paint
on
any
gouges
in
the
finish
caused
by
assembly
tools.
PROCEDURE
FOR
INSTALLATION:
1.
Prepare
proper
concrete
slab
as
required.
2.
Freestanding
bench
ships
with
glides
installed.
Bench
can
be
set
in
place.
Important!
•
Do
NOT
drag
bench
across
concrete
or
other
rough
surfaces.
•
Do
NOT
lift
the
bench
by
the
arms
•
Do
NOT
lift
the
backed
bench
by
the
back
panel.
•
Do
NOT
drop
the
bench
– lower
gently
into
place.
For
SURFACE
MOUNT
bench:
1.
Tip
bench
onto
protective
material.
Leave
glides
installed.
2.
Install
surface
mount
tab
on
each
support,
as
shown
in
Fig.
1.
3.
Set
bench
in
place
and
mark
hole
locations.
4.
Move
bench
and
drill
holes
according
to
diameter
and
depth
required
by
surface
mount
anchor
manufacturer.
Clear
holes
of
debris.
5.
Set
bench
back
in
position
and
install
surface
mount
anchors
per
manufacturer’s
instructions.
For
EMBEDDED
bench:
1.
Tip
bench
onto
protective
material.
Remove
glides.
2.
Install
threaded
rods
into
supports
as
shown
in
Fig.
2.
3.
Support
bench
and
set
into
position.
4.
Trace
around
threaded
rods
to
mark
hole
locations.
5.
Move
bench
and
drill
holes
per
anchoring
epoxy
manufacturer’s
recommendations.
Clear
holes
of
debris.
6.
Test
fit
bench
into
position,
ensuring
that
the
threaded
rods
are
not
resting
on
the
bottom
of
the
drilled
holes.
7.
Remove
bench
and
fill
holes
with
epoxy.
8.
Set
bench
in
position.
Wipe
away
excess
epoxy
before
it
begins
to
cure.
To
adjust
leveling
glides:
1.
The
stainless
steel
glides
have
flat
sides
to
allow
a
1
‐
1/4”
thin
wrench
to
adjust.
Included
components:
•
Bench
ships
fully
assembled
•
For
surface
mount:
(2)
each
surface
mt tabs,
3/8
‐
16
x
5/8”
Flat
head
cap
screws
•
For
embedded:
(4)
3/8
‐
16
threaded
rods
Tools
Required
for
Surface
mount
or
Embedded
option:
•
Safety
glasses
•
Hammer
drill
with
masonry
bits
•
(2)
non
‐
corrosive
anchors,
max
3/8”
diameter
(surface
mount
option)
•
7/32”
hex
key
(surface
mount
option)
•
1
‐
1/4”
thin
wrench
for
adjusting
or
removing
freestanding
glides
•
Chemical
anchoring
adhesive
(Hilti
HIT
RE
500
or
equivalent)
(embedded
option)
•
Proper
lifting
equipment
with
protective
padding
(benches
weigh
between
280lbs
‐
345lbs)
Installation Guide
STRATA
Beam Bench
www.landscapeforms.com Ph: 800.521.2546
Date: March 27, 2018
Page 1 of 2
2x
– surface
Mount
tabs
2x
– FHCS
(surface
mt only)
4x
– threaded
rod
(embedded
only)
Straight,
backless
Straight,
backed
