Included
Components
•
(1)
Tabletop
•
(1)
Table
Support
•
For
Catena
or
Steelhead
table
top:
(4)
1/4
‐
20
x
3/4"
Phillips
truss
head
tapping
screws
•
For
Marneaux®
table
top:
(4)
1/4
‐
20
x
5/8”
Phillips
machine
screws
with
washers
For
umbrella
option:
Any
Landscape
Forms’
umbrella
secures
directly
to
all
table
supports.
Additional
umbrella
surface
mount
stand
is
not
required
for
use
with
tables.
•
Umbrella
connection:
(1)
1/4
‐
20
Phillips
pan
head
machine
screw
and
(1)
lock
nut
‐
2
‐
3/4”
length
for
Ø18”
Catena
base
‐
3
‐
1/4”
length
for
Ø23”
Catena
base
Tabletop
Assembly:
Note:
For
Catena
Support
Option:
Use
Ø18”
support
for
24”
and
30”
tables.
Use
Ø23”
support
for
all
others.
1.
Place
table
top
upside
down
on
non
‐
marring
level
surface.
2.
Place
table
support
upside
down
on
table
top
and
align
holes.
The
use
of
power
drivers
is
not
recommended.
Threads
or
threaded
inserts
may
be
damaged
or
broken
due
to
over
‐
torqueing.
3.
Install
hardware.
Tighten
all
table
top
fasteners
until
snug,
then
tighten
additional
1/4
turn.
4.
Turn
table
right
side
up
using
at
least
two
people.
5.
Freestanding
table
can
be
set
in
position.
Surface
Mount
Installation:
1.
Place
unit
in
desired
position.
2.
Mark
the
holes.
3.
Move
the
unit
and
drill
the
holes.
4.
Place
unit
in
position
and
install
with
anchors
according
to
anchor
manufacturer’s
recommendations.
Catena
Stainless
steel
Or
powdercoat
Steelhead
Perforated
Steelhead
Solid
Marneaux®
Tools
Required
•
For
Catena,
Steelhead,
or
Marneaux®
table
top:
#3
Phillips
screwdriver
•
For
umbrella
option:
#3
Phillips
screwdriver
and
7/16”
wrench
•
(3)
Non
‐
corrosive
anchors,
maximum
Ø3/8”
[9mm].
ASSEMBLE
WITH
CARE!
Pangard II
Polyester
Powdercoat is
a
strong,
long
‐
lasting
finish.
To
protect
this
finish
during
assembly,
place
unwrapped
powdercoated parts
on
packaging
foam
or
other
non
‐
marring
surface.
Do
not
place
or
slide
powdercoated parts
on
concrete
or
other
hard
or
textured
surface
– this
will
damage
the
finish
causing
rust
to
occur.
Use
touch
‐
up
paint
on
any
gouges
in
the
finish
caused
by
assembly
tools.
Installation Guide
Tables
Marneaux®, Catena, Steelhead Tabletops with Catena support
www.landscapeforms.com Ph: 800.521.2546
Date: May 21, 2018
Page 1 of 2
Umbrella
Assembly:
1.
To
install
umbrella,
slide
umbrella
pole
through
hole
in
table.
2.
Align
holes
in
base
tube
and
umbrella
pole.
Insert
long
1/4
‐
20
machine
screw
and
secure
with
lock
nut.
CAUTION:
Do
not
let
go
of
the
umbrella
until
the
pole
has
been
secured.
Recommended
hardware:
Although
installer
is
responsible
for
anchoring
procedure
and
hardware,
we
suggest
the
following:
For
poured
concrete
installation:
•
3/8"
diameter
wedge
or
sleeve
type
expansion
anchor
at
least
3"
long,
or
3/8”
‐
16
x
4”
threaded
anchor
rod
with
anchoring
adhesive
For
paver
installation:
•
If
pavers
are
installed
over
poured
concrete,
use
3/8"
diameter
wedge
type
expansion
anchor
with
enough
length
to
go
through
brick
and
into
concrete
For
wood
deck
installation
(at
least
2"
nominal
thickness):
•
3/8"
hex
head
lag
screw
at
least
2"
long
