casual
ht SUPPORT
‘A’
1X
– 3
seat
ASSEMBLE
WITH
CARE!
Pangard II
Polyester
Powdercoat is
a
strong,
long
‐
lasting
finish.
To
protect
this
finish
during
assembly,
place
unwrapped
powdercoated parts
on
packaging
foam
or
other
non
‐
marring
surface.
Do
not
place
or
slide
powdercoated parts
on
concrete
or
other
hard
or
textured
surface
– this
will
damage
the
finish
causing
rust
to
occur.
Use
touch
‐
up
paint
on
any
gouges
in
the
finish
caused
by
assembly
tools.
Tools
required:
•
protective
padding
•
Phillips
head
screwdriver
•
Non
‐
corrosive
anchors,
maximum
Ø3/8”
[9mm]
– 3
for
3
‐
seat
unit,
4
for
4
‐
seat
unit
•
9/16”
wrench
(for
seats)
•
5/32”
hex
key
•
7/16”
wrench
(for
umbrella
hardware)
WARNING!
TABLES
MUST
BE
FASTENED
SECURELY
TO
HARD
SURFACING
TO
PREVENT
TIPPING.
Installation Guide
Carousel
casual height table
www.landscapeforms.com Ph: 800.521.2546
Date: June 21, 2018
Page 1 of 2
Included
components:
•
Support
‘A’
with
surface
mount
tabs
•
Support
‘B’
with
surface
mount
tabs
•
Seats
(qty and
style
depends
on
order)
•
1
tabletop
per
unit,
with
attaching
hardware
•
(1)
¼
‐
20
x
2
‐
1/4”
Phillips
pan
head
machine
screw
and
lock
nut
casual
ht SUPPORT
‘B’
1X
– 3
seat
1X
– 4
seat
casual
ht SUPPORT
‘A’
1X
– 4
seat
30”
dia tabletop,
Marneaux
or
Catena
27”
square
wood
Tabletop
30”
dia wood
Tabletop
30”
square
Marneaux
Tabletop
Backless
Grid
seat
Backless
perf
seat
Backed
grid
seat
Backed
perf
seat
Hoop
seat
1X
per
seat
‐
3/8
‐
16
x
1
‐
1/2”
indented
hex
head
machine
screw
1X
per
seat
–
3/8
washer
TABLETOP
ASSEMBLY:
See
Fig
1
and
Fig
2.
Note:
DO
NOT
DRAG
unit
across
concrete
or
other
rough
surfaces.
This
could
damage
the
powdercoat on
the
bottom
of
the
surface
mount
tabs.
1.
Verify
that
surface
mount
tabs
are
securely
fastened
to
support
legs.
Tighten
if
necessary.
2.
Place
table
top
upside
down
on
non
‐
marring
level
surface.
3.
Place
table
support
“A”
(has
5”
ring
at
center)
upside
down
on
table
top
and
align
holes.
4.
Loosely
fasten
support
to
table
top
with
screws
provided.
‐
Catena/Steelhead
tables
include
(12)
1/4
‐
20
x
3/4”
Phillips
truss
head
tapping
screws
‐
Marneaux®
includes
(4)
1/4
‐
20
x
3/4”
Phillips
pan
head
machine
screws
and
washers.
One
screw
required
at
the
outer
hole
in
each
plate.
‐
Square
wood
tabletop
includes
(12)
1/4
‐
20
x
1”
Phillips
pan
head
machine
screws.
5.
Hold
table
support
“B”
upside
down
and
carefully
lower
it
over
support
“A”
so
bar
on
“B”
fits
into
notch
on
“A”.
Loosely
fasten
support
“B”
to
table
top.
The
use
of
power
drivers
is
not
recommended.
Threads
or
threaded
inserts
may
be
damaged
or
broken
due
to
over
‐
torqueing.
6.
Install
hardware.
Tighten
all
table
top
fasteners
until
snug,
then
tighten
additional
1/4
turn.
7.
Turn
table
right
side
up
using
at
least
two
people.
PROCEDURE
FOR
ASSEMBLING
SEATS:
See
Fig
3.
Note:
These
instructions
apply
to
all
seat
styles
for
Carousel
units.
Seats
were
NOT
designed
to
swivel.
Allowing
the
seat
to
swivel
will
damage
the
finish
and
the
product.
1.
Slide
seat
stem
into
tube
on
support.
Backless
seats
should
be
installed
with
the
flat
part
of
the
stem
facing
in
toward
the
center
of
the
table.
2.
Align
threaded
hole
in
seat
stem
with
hole
in
support
tube.
This
may
require
lifting
the
seat
slightly.
3.
Insert
washer
and
hex
head
machine
screw
through
the
support
hole
and
tighten.
Screws
are
coated
with
a
dry
thread
locking
compound
that
cures
in
24
hours.
Wiggle
seats
and
tighten
as
necessary
until
seat
is
securely
fastened.
