Landis S755 (G2) Operator'S Manual Download | Manualshive

Page: 19 / 28

background image

Operator Manual S755 (G2) / S755 XL (G2)

October 2017

Landis International - 19

FILTERS

Change them (3 units) when necessary (SKU: G8PM300399).
Put the green side towards the outside of the machine.

TRIMMER CUTTER

1.

Check trimmer cutter condition daily.

2.

Check for wear on hardened steel cutters and sharpen if
necessary.

For carbide cutter, return to Landis for sharpen

.

3.

Check for broken teeth on the carbide cutter, if supplied with
your machine, replace cutter.

4.

Clean with the air jet the trimmer section.

V-BELT

1.

Check the belt with a complete turn by turning the sole trimmer.

2.

Check its condition. If it is cracked, replace it.

•

MOTOR REPLACEMENT REQUIRES WORKING WITH 220 VOLTS ELECTRICAL WIRING AND CAN BE
HAZARDOUS. PLEASE CALL A QUALIFIED ELECTRICIAN OR A LANDIS TECHNICIAN.

MOTOR

Clean each side of the motor and the wheels with a vacuum cleaner or an air
jet.

If you believe that the motor present an anomaly, please contact our customer
service at 1 800 634-0806.

Worn carbide cutter

«
...
17
18
19
20
21
...
»

Summary of Contents for S755 (G2)





























Reviews:

No comments

Related manuals for S755 (G2)

Brand: Duplo Pages: 142

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands