Land Pride 944730, Operator'S Manual

Page: 68 / 72

Section 7: Features & Benefits
Table of Contents
RC5615, RC6615, RCM5615, & RCM6615 Series 2 S/N Rotary Cutters 330-323M 5/6/20
62
RC(M)5615 & RC(M)6615 Series 2
Features Benefits
Surpassed rugged industry
standards All Land Pride Cutters have been designed and tested to meet rigorous voluntary testing
procedures according to ISO 4254-13.
Factory assembled Saves customer set-up time and money.
7 Year gearbox warranty
Shows confidence in gearbox integrity. (Years 6 & 7, parts only.)
Rugged heavy built gearboxes Capable of handling heavy cutting applications.
Gearbox Seal Protection Gearbox bottom seal protection for longer bearing life.
2 3/8" Output gearbox shaft
Large output shaft handles shock loads better.
2 Piece shield on wing gearboxes Driveline grease zerks are easier to access.
Self-leveling hitches Reduces drawbar wear by keeping hitch level while going through ditches.
Low hitch weight on tractor tongue
Ideal for smaller horsepower tractors by reducing the amount of weight on the drawbar.
Narrow A-frame hitch Allows for a tighter turning radius.
Adjustable park jack angle Park jack can be adjusted to be perpendicular to the ground.
Adjustable driveline hanger
Serves as a support rest for the driveline when the cutter is unhooked from the tractor.
Assist operator when attaching driveline to tractor power take-off shaft.
Input driveline:
Cat. 6 CV or Cat. 5 conventional
Holds up to shock loads and harsh mowing conditions. Constant velocity (CV) U-joint
allows for 80 degree turns without doing damage to the driveline.
Drivelines with slip-clutches:
RC56 Series: Cat. 4 standard
RC66 Series: Cat. 5 standard
Driveline is sized right for the intended cutting capacity.
Slip-clutches will slip under load to minimize twist damage to driveline profiles.
Grease zerks on end caps of
driveline cross journals
Intermediate and wing driveline cross journals are easier to grease.
All drivelines have access holes for greasing the U-joints and inner profiles.
High blade tip speed
Allows clean cutting of material and even distribution.
6" Blade overlap Eliminates skipping during turns.
High cutting capacity Can cut brushy areas with saplings up to 4" with 56 Series and 4 1/2" with 66 Series.
Pre-cut chamber
Allows grass and vegetation to stand back up prior to cutting for a more complete cut.
Reinforced leading deck edges Front of deck can withstand heavy brush and saplings.
12" Deck height Handles heavy cutting, which reduces balling-up of cut material under the deck.
10 Gauge smooth deck top
Reduces accumulation of debris and is easier and faster to clean.
7 Gauge smooth deck bottom Heavy deck design holds up to harsh conditions. No bottom obstructions.
Replaceable 1/4" side skirt Reduces debris piercing possibilities. Can be replaced if damaged.
Left wing rotates clockwise
Better discharge of material. Picks up tractor tracks.
3/16" Stump jumper backed with a
1" thick mounting bar
Heavy round stump jumper. Can hold up to tough conditions.
Beveled skid shoes on wings Reduces gouging the ground when turning.
LED Signal lights
LED lights are bright, long lasting, and resistant to vibration, unlike incandescent
counterparts.
Hinged wing sections
Allows
cutter
to follow terrain. Ideal for rough ground where hillsides, ditches, and
hollows can cause uneven cutting.
Greasable wing folding hinges Provides for a long hinge life and allows wings to fold up and down with less stress.
1" Solid hinge rods Gives greater strength to the
cutter
from front to rear, and in the hinge area itself.
Wing transport locks
Holds transport wings in the folded-up position in case of hydraulic pressure loss.
Collapsible 1" leveling rods
Prevents damage and failure to leveling rods. Large diameter leveling rods provide
superior supporting strength over rough terrain.
Enclosed dual leveling rods C
utter
pulls equally on the rear axle while traveling over rough terrain.
5-Bolt hubs on trailing arms 5-Bolt hubs makes the wheel assembly more durable and longer lasting.
Drain holes in wheel rims
Allows water to drain from wheels mounted on folded-up wings.
Helps prevent paint deterioration and rusting to the wheel rims.
Spring-cushioned trailing arms
Provides independent suspension, cushions loads on drawbar.
Replaceable wheel spindles
Wheel spindles can be replaced when damaged without replacing the entire axle.
Simply remove one bolt to replace damaged spindle.
Wheel options
Laminated tires:
Eliminates flats.
Air-filled tires: Give better cushion while transporting.
Foam-filled tires:
Give better cushion while transporting and can’t go flat.
LP Performance hitch option
Great for uneven terrain, reduces drawbar wear. Hitch pivots freely up and down and
pivots about the tractor drawbar.
Bar-tite hitch option Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear.
Roadway light kit option
Allows operator to transport on public roads safer when head lights are turned on
and/or when flasher lights are turned on.
Deck ring option Keeps blades from damaging the deck.
Section 7: Features & Benefits