manualshive.com logo in svg

Lancom L-54 dual Wireless, Manual, Page: 20 / 81

Share
Download
Lancom L-54 dual Wireless Manual Download Page 20

LANCOM L

-

54g Wireless -  LANCOM L

-

54ag Wireless -  LANCOM L

-

54 dual Wireless

 Chapter 2: Installation

19

EN

ing with PoE in the info box ’Power-over-Ethernet – elegant power supply
through the LAN wiring’ 

→

Page 20.

By activated DSLoL option, the LAN connector can also be used for con-
necting the LANCOM Access Point to a broadband modem.

(First) Ethernet connector.

Connection for the serial configuration cable.

Main connector for the (second) WLAN module. Additional AirLancer
antennas are connected to the Main connectors if necessary.

Reset switch – has two different functions depending on the length of
time that it is pressed. 

Main connector for the (first) WLAN module. 

Reset switch of LANCOM L-54 dual Wireless 

The reset button offers two basic functions—boot (restart) and reset (to the
factory settings)—which are called by pressing the button for different
lengths of time. 

Some devices simply cannot be installed under lock and key. There is
consequently a risk that the configuration will be deleted by someone
pressing the reset button too long. With the suitable setting, the behavior of
the reset button can be controlled accordingly.

Reset button

This option controls the behavior of the reset button when it is pressed:

Ignore: The button is ignored.

Please observe the following notice:

 The settings 'Ignore' or 'Boot

only' makes it impossible to reset the configuration to the factory set-
tings using the reset button.

If the password is lost for a device with this setting, there is no way to
access the configuration! In this case the serial communications inter-
face can be used to upload a new firmware version to the device-this
resets the device to its factory settings, which results in the deletion

Configuration tool

Call

WEBconfig, Telnet

Expert configuration > Setup > Config

Summary of Contents for L-54 dual Wireless


















































































Reviews:

No comments