Lancaster 7-LXC-50, Installation, Operating And Service Manual

Page: 18 / 30

PAGE 18
DRAIN LINE - 3/4”
Dwg
No.
Order No. Description Qty
1 H4615 Elbow Locking Clip 1
2 V3194 Polytube insert 5/8 Option
3 V3192 Nut ¾ Drain Elbow Option
4* V3158 Drain Elbow ¾ Male 1
5 V3163 O-ring 019 1
6* V3159 DLFC Retainer Assy 1
7
V3162-007 DLFC 0.7 gpm for ¾
One
DLFC
must
be
used
if ¾
fitting
is
used
V3162-010 DLFC 1.0 gpm for ¾
V3162-013 DLFC 1.3 gpm for ¾
V3162-017 DLFC 1.7 gpm for ¾
V3162-022 DLFC 2.2 gpm for ¾
V3162-027 DLFC 2.7 gpm for ¾
V3162-032 DLFC 3.2 gpm for ¾
V3162-042 DLFC 4.2 gpm for ¾
V3162-053 DLFC 5.3 gpm for ¾
V3162-065 DLFC 6.5 gpm for ¾
V3162-075 DLFC 7.5 gpm for ¾
V3162-090 DLFC 9.0 gpm for ¾
V3162-100 DLFC 10.0 gpm for ¾
*4 and 6 can be ordered as a complete assembly -
V3331 Drain Elbow and Retainer Assy
Order No: V3007 (Standard)
Description: Fitting 1” PVC Male NPT Elbow
Assembly
Drawing
No.
Order
No.
Description Quantity
1 V3151 Nut 1” Quick Connect 2
2 V3150 Split Ring 2
3 V3105 O-Ring 215 2
4 V3149 Fitting 1 PVC Male
NPT Elbow
2
















Order No. V3191-01 (Optional)
Description: Fitting Vertical Adapter Assembly
Drawing
No.
Order
No.
Description Quantity
1 V3151 Nut 1” Quick Connect 2
2 V3150 Split Ring 2
3 V3105 O-Ring 215 2
4 V3191 Vertical Adapter 2
INSTALLATION FITTING ASSEMBLIES







4
Water
Flow
Proper DLFC orientation
directs water flow towards
the washer face with
rounded edge.
Refer to specification page 11 for correct DLFC size per model.
Do not use pipe dope or other sealants on threads. Teflon tape must be used on threads of 3/4” NPT connection (unless
using 5/8” polytubing).
Do not use Vaseline, oils, other hydrocarbon lubricants or spray silicone anywhere. A silicone lubricant may be used on
black o-rings but is not necessary.
Do not use pipe dope or other sealants on threads. Teflon tape must be used on threads of 1” NPT connection. Teflon
tape is not necessary on the nut connection nor caps because of o-ring seals.
The nut and caps are designed to be unscrewed or tightened by hand or with the service spanner wrench (see page 19).
If necessary a pliers can be used to unscrew the nut or cap. Do not use a pipe wrench to tighten or loosen nuts or caps.
Do not place a screwdriver in slots on caps and/or tap with a hammer.
Do not use Vaseline, oils, other hydrocarbon lubricants or spray silicone anywhere. A silicone lubricant may be used on
black o-rings but is not necessary.
3
2
1
4