background image

3

1   Important Information about the Manual

1

Important Information about the Manual

These instructions must be read carefully and completely before commencing with any work. 

The basic prerequisite for working safely is compliance with all the specified safety instruc

-

tions.

1.1

Purpose/Applicability of the Document

These instructions facilitate the safe and efficient handling of the pilot burner GFI and its

variants.
The devices correspond to the following directives and standards:
European Directives:
• 2014/30/EU (EMC Directive) (only F130I and display) 
• 2015/35/EU (Low Voltage Directive)
• (EU) 2016/426 Gas Appliance Directive (GAR)
• 2014/34/EU ATEX Directive (only devices of Ex-Zone 1 and 2)
• 2011/65/EU (RoHS2)

Harmonised European Standards:
• DIN EN 298 (only integr. flame monitoring F130I)
• DIN EN 13611 (only integr. flame monitoring F130I)
• DIN EN 61508 (only integr. flame monitoring F130I)
• IEC 60079-0 (only devices of Ex-Zone 1 and 2)
• IEC 60079-1 (only devices of Ex-Zone 1)
• IEC 60079-7 (only devices of Ex-Zone 2)
• IEC60079-15 (only devices of Ex-Zone 2)

Approvals:
• SIL3 (only integr. flame monitoring F130I)

Indien:
• Petroleum Rules, 2002 (only devices of Ex-Zone 1 and 2)

1.2

Target Group

NOTICE

All assembly, commissioning, troubleshooting and maintenance work may only be carried 

out by authorised and trained personnel. 

The device may be operated and maintained only by those who are capable of doing so 

in terms of their level of knowledge and training. 

For safety reasons, access to parameter settings must be restricted to authorised and 

trained personnel.

Summary of Contents for GFI35















































Reviews: