background image

2

Display

2000 count, Dual function 3 ½ digit LCD with Bar 

graph

Display size

24 mm x 20 mm

Sensor

Polarographic type

Membrane 

Bonded membrane cap with threaded fitting

Operating Temp.

Range 0 to 50°C (32 to 122°F)

ATC Range 

0 to 50°C (32 to 122°F)

Salinity Compensation  0 to 50 ppt in 1 ppt (part per thousand) increments

Altitude compensation  6000 m (0 to 20,000 ft) in 300m (1000 ft) increments

Measurement Storage  25 tagged (numbered) data sets with recall

Battery Power

Four (4) CR2032 button batteries

Low Battery Indication ‘BAT’ appears on the LCD

Auto Power Off 

After 10 minutes of inactivity (APO override available)

Dimensions/Weight

36 x 173 x 41mm (1.4 x 6.8 x 1.6”); 110g (3.8 oz)

Measurement

Range

Resolution

Accuracy

% Saturation

0 to 200.0%

0.1%

±2.0% FS (full scale)

Dissolved Oxygen 0 to 20.00 mg/l 0.01 mg/l

±2% FS

Concentration

0 to 20.00 ppm 0.01 ppm

±2% FS

Temperature

0 to 50 °C

0.1 °C

±1.0 °C

32 to 122°F

0.1 °F (0 to 99ºF);  

1.0 °F (>100°F)

±1.8°F

CONTENTS

Dissolved Oxygen TRACER Kit, Code 1761
Includes:  DO TRACER Body, DO Bonded Membrane Cap Assembly Electrolyte 

Solution, Sample cup and Lanyard

PARTS & ACCESSORIES

DO Replacement Sensor Kit (sensor module, membrane cap assembly, 

electrolyte solution)  Code 1762
DO Membrane Cap Kit (6 membrane cap assemblies, electrolyte solution, 

Polishing Strips)  Code 1761M
DO Extension Cable, 1 meter (with probe guard and weight)  Code 1763
DO Extension Cable, 5 meter (with probe guard and weight)  Code 1764

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for Tracer PockeTester













Reviews: