background image

 

Manual SmartPicker AOM Rev. A ENG 

LaCoSys Nov 2017  

-12-

 

4

 

Use of the device 

4.1

 

Unpacking and installation 

Please  verify  the  packaging  if  it  is  damaged.  Any  damage  must  be  announced  to  the  carrier  and  the 
manufacturer after receipt. Please verify if the package is complete: 

 

 

 

 

 

 

 

4.2

 

First steps 

Connect the mains cable with the delivered power supply and connect the DC-Pug to the device. 

 

Only use the delivered power supply! 

 

Connect a USB A-B 

 cable with the device and your PC.  

 

You  may  need  administrator  rights  to  install  the  necessary  software  drivers  depending  on  the 
operating system.  

 

The  software  driver  installation  proceeds  automatically  if  Microsoft  Windows  7  or  higher  is  used.  For  more 
information please read chapter 4.3. 

 

 

Fig. 4: 

Scheme of a set-up 

 

A possible set-up of the SmartPicker AOM with a AOM-Driver and modulator is depicted in Fig. 4. Your set-up 
may differ from this. The oscilloscope  can used on monitor ports for the visibility of the electrical pulses for 
modulator control. 

 

Description 

Number 

SmartPicker tabletop device 

Mains cable 

Documentation (manual, usb-stick) 

Power supply  

Summary of Contents for SMART PICKER SERIES





















Reviews: