Introduction
The MRX700 converts the SCART output from
a set top box to an RF2 output which will power
DigiLink eyes allowing viewing and control
from TV sets around the home.
With an additional RF output for your main TV
and optional SCART loop-through.
Compatible with old and new Sky™, Sky+™
and Sky+HD™ boxes* also compatible with
Freesat™/ Freeview™ receivers & PVRs.
• Comes with two IR transmitters for control of
up to two devices (connected via the SCART IN)
• RF2 DC output 9VDC, 100mA to power DigiLinks
• RF2 output suitable for distribution via
DigiLink compatible amplifiers.
• RF IN allows aerial and CATV signal distribution
• Fully compatible with new and existing TV
distribution systems
• Allows the use of existing RF Link devices used to
distribute Sky™ signals and control remotely Sky™receivers
Please Note: Older Sky boxes with RF2 outputs
can be connected via the MRX700 RF input
and additional STB(s) via the SCART.
Newer Sky boxes with no RF output will need
to be connected via the LabLink SCART input.
MRX700 - DigiLink SCART to RF Converter Kit
compatible with new Sky™/Freesat™/Freeview™ receivers & PVRs
For further information or any queries please contact
Customer Careline: 08457 573 479
(Local rate – UK only)
www.labgear.co.uk
Waste electrical products should not
be disposed of with household waste.
Please recycle where facilities exist.
Check with your Local Authority for
recycling advice.
© Philex Electronic Ltd. 2014 V1.1
Labgear Reserve the right to modify their designs or specifications, In the light of future developments, without
prior notice. Performance figures quoted are typical and subject to normal manufacturing and service tolerances
General Safety Precautions
• To prevent fire or shock hazard, do not
expose this device to rain or moisture.
• This product is for indoor use only
• Do not expose the product to extreme heat
• Do not use the product close to water.
• Do not open this unit it contains no user
serviceable parts. Refer servicing to
qualified personnel only.
• This device should be operated using only
the power supply included with it or one
with an identical rating.
• Do not overload wall outlets and extension
cords as this can result in the risk of fire or
electrical shock.
Care
To clean wipe gently with a soft non- abra-
sive cloth. The cloth can be slightly moist-
ened with a diluted mild detergent solution
providing the aerial is first switched off and
disconnected from the power supply.
4
1
Specifications and Safety Precautions
1
7
8
2
3
4
6
1
5
7
8
2
9
4
6
9
5
10
10
AV Input
- SCART Socket for audio and
video signal input.
AV Output
- SCART Socket for audio and
video signal by-pass output
Power Switch
- Turns power ON/OFF.
Power Display Window
- Red LED indicates
power ON/OFF
IR Socket
- Connection for IR transmitters.
RF2 output
- 1. Modulated AV signal combined
with RF IN signal - also provides DC 9V/100mA
(max.) to power DigiLink
RF1 Outpu
t - Modulated AV signal combined with
RF IN signal output from this port
RF IN Port
- Input for aerial / CATV signals with
0~5dB bandwidth gain.
DC Input
- Connection for 9VDC/600mA power adaptor.
IR Transmitters
- Placed over IR sensors of STBs to
transmit remote control signal from remote location
1
7
8
2
3
4
6
9
5
10
Modulator
Standard:
PAL G / I
Frequency:
UHF 470 - 860MHz
Output Level:
72±4 dBµV
Gain:
0-5dB (RF in to RF out)
Sound system:
Mono
Power Supply Input:
110-220V~50/60Hz, 0.25A
Power Supply Output: 9V
𝌂
600mA
Video input:
1.0Vp-p/75Ω
Audio input:
1.0Vp-p/600Ω
DC output (RF2):
9VDC/100mA (max.)
A/V Connector:
SCART sockets
RF Connector:
F type
Dimensions:
116mm x 78mm x 35mm
Weight:
115g
IR Transmitter
Connector:
3.5mm Socket
Peak wavelength:
940nm
View Angle:
40˚
Cable length:
800mm
Specifications
