Labcyte Echo 520 User Manual Download Page 8 | Manualshive

Page: 8 / 200

Labcyte Echo 520 User Manual Download Page 8

viii

Echo Liquid Handler

U

ser Manual

Safety warnings and precautions

The Echo liquid handler has been designed for safe operation.

The safety warnings and precautions in this section and throughout the
manual must be observed during installation, relocation, maintenance,
repair, and normal operation of an Echo liquid handler.

Failure to comply with these warnings and precautions, or with specific
cautions and warnings found elsewhere in this manual, violates the safety
standards of design, manufacture, and intended use of an Echo liquid
handler. This can result in hazardous exposure to laser light, high voltage,
or moving parts. Exposure to these hazards can cause severe injury.

Safety notation marks

This manual uses the following symbols in the left margin to draw your
attention to the specified type of information.

Symbol

Meaning

Warning

Warnings alert all users to the following:



Potentially hazardous conditions



Actions that may result in personal injury or death

Caution

Cautions alert the user to actions that may result in the
following:



Damage to the equipment



Lost or corrupted data



Unrecoverable interruption of the operation being
performed

Note

Notes emphasize or expand upon the surrounding
information.

«
...
6
7
8
9
10
...
»

Summary of Contents for Echo 520









































































































































































































Reviews:

No comments