background image

S1 Dream-T Espresso Machine

 

 

Owner’s Manual 

Page 4 

 

button to start filling the coffee boiler. 
 

  Keep holding the button until you have water coming out of the group head for at least 

20 seconds. When done press the 

 button to return to standby mode. 

 

  After filling the coffee boiler then refill the water reservoir before turning the machine on 

so there will enough water to fill the steam boiler. 

 
 

Turning the machine on for the first time 

 

WARNING:

 

DO NOT turn the machine on until the steps above have been completed. 

Failure to do so will damage the machine and will not be covered under warranty.

 

 

  Press and hold the

 button for approximately 3 seconds until the display lights up. The 

pump will come on to start filling the steam boiler and will turn off once it is filled. 
 

  Whichever portafilter you intend to use then lock it into the grouphead so it will warm up  

with the machine. 
 

  If you plan on using the steam boiler for steaming milk then press the 

 button. 

 

  Allow the machine to heat up for at least 30 minutes for optimal performance and 

temperature stability. It is very important to keep the portafilter in the grouphead and 
also keep the cups on the cup warming tray. Failure to do so will result in a cold and 
sour shot.  
 

  Set the grind particle size on your grinder. This is very important to achieve good 

results. Set the grind so that a 2oz double shot comes out in about 25 seconds.  
The grind should be finer than salt, but coarser than powder.  

For grinder set up tips check out our video here: 

http://vimeo.com/48806806

  

Basic machine operation 

 
 

Turning The Machine On And Off

 To turn the machine on press and hold the 

 button for 

approximately 3 seconds until the machine turns on.  
 
To turn the machine off quickly press the 

 button. (Do not hold button down) 

 

Pulling Shots

 There are a few ways you can pull a shot with the S1 Dream-T. You can use one 

of the two programmable shot buttons, single 

 or double

. These buttons can be 

individually programmed for volume and temperature. The shots will automatically stop 
dispensing at the desired level or you can press the same button again to stop the shot at any 
time. 

Summary of Contents for S1Dream-T























Reviews: