MANUAL FOR USE AND MAINTENANCE
LSC 006 REV. 01
9
REGULATION OF THE OPERATING TEMPERATURE OF THE MACHINE
1
When the machine is on, press the ON//OFF (27) button and keep it pressed for 3 seconds: the control
light (22) and the one concerning the set temperature start flashing. For example, if the set temperature
is 105
°
C the control light (18) starts flashing.
LIGHT N. 13
14
15
16
17
18
19
20
21
22
TEMP.
85
90
95
100
105
110
120
130
°
C
2
In order to change the operating temperature, press and release the hot water delivery button (23); to
every pressure of the button corresponds an increase of the temperature of 5
°
C (with the flashing of the
corresponding control light). When the maximum temperature of 130
°
C (control light 21) is reached, the
selection restarts from the minimum temperature of 85
°
C (control light 14) (cyclic mode).
3. Once you choose the desired temperature, in order to confirm the datum, press the ON/OFF (27) button,
the machine will then go back to its standard operating phase.
In order to have a fine tuning temperature setting of 1
°
C increment of the coffee delivery group temperature
proceed as follows:
•
Switch the machine off pressing the ON/OFF button (27), the green control-light (22) from fixed turns to
flashing (STAND BY MODE).
•
Press and keep pressed for about 3 seconds the button STOP (25A) or the 2 cup button (25) in the
automatic version, the leds 17 and 18 turn on to indicate that one has entered the fine tuning temperature
setting of 1
°
C increment.
•
To every pressure of the steam delivery button (26) the leds 19,20, 21 turn on gradually where every led
corrisponds to a 1
°
C increment of the temperature set, whereas to every pressure of the coffee button
(24 A) or the one cup button (24) in the automatic version, the leds 16,15, 14 gradually turn on and here
every led corresponds to a 1
°
C decrement of the temperature set. For example, if the set temperature
is 105
°
C and you proceed to turn on the leds 19 and 20, the new set temperature becomes 105 +2 =
107
°
C.
The value of the operating temperature of the machine can be changed only in order to improve the final
result in the cup, according to the coffee blend used.
3.1
DOSE SETTING (ONLY IN THE AUTOMATIC VERSION)
1. When the machine is on (control light 22 on and fixed), press the ON//OFF (27) button and keep it pressed
for about 3 seconds; the control light (22) and the one concerning the set temperature start flashing.
2. Fill with ground coffee the one cup filter of the filterholder (11), (using the coffee doser provided), making
sure not to leave coffee powder residues on the upper edge of the filterholder, and press it with the
suitable coffee tamper provided.
3. Fasten the filterholder (11) to the brewing group (10) and place a cup below the filterholder.
4. By pressing the one cup button (24) the delivery starts and the control lights 14-15-16 turn on to show
that the 1 coffee dose is being programmed.
5. When the coffee inside the cup has reached the desired quantity, press again the button (24) to stop the
delivery.
6. You automatically return to the initial visualization.
7. Fill with ground coffee the the two cup filter of the filterholder (11) (using the coffee doser provided),
making sure not to leave coffee powder on the upper edge of the filterholder, and press it with the suitable
coffee tamper provided.
8. Fasten the filterholder (11) to the brewing group (10) and place two cups below the filterholder.
9. By pressing the two cup button (25) the delivery starts and the control lights 17-18-19 turn on to show
that the two coffee dose is being programmed.
10. When the coffee inside the cup has reached the desired quantity, press again the button (25) to stop the delivery.
11. You automatically return to the initial visualization.
3
Summary of Contents for S1 Rossini
Page 2: ......
