background image

19 | 

P a g e

 

 

If a miss happens: 

 

If sensor loses connection to the station for any reason, the station will show dashes after 30 

minutes.  

 

The station will search for 5 minutes every hour to reconnect with sensor.  

 

Be sure you have good 

batteries

Manually search for your sensor. 

 

Try this: 

 

Bring your sensor within 10 feet of your station and make sure it is connected to the station.  

 

After 15 minutes move the sensor into the next room with a wall between the sensor and the 

station for 1 hour.   

 

If there is no loss of signal in that hour, move the sensor just outside. 

 

Continue moving the sensor back to its original location. 

 

If you lose connection, look for sources of 

interference.

 

 

WHY AM I GOING THROUGH BATTERIES QUICKLY? 

 

 

Test a new set of 

batteries.

 Write down the date of installation and the voltage of the 

batteries. 

 

When the batteries fail, please note the date and voltage again. This is helpful in determining 

the problem. 

 

Check for leaking batteries, which may damage the sensor. 

HOW DO I CHANGE BETWEEN FAHRENHEIT AND CELSIUS? 

 

 

On your sensor, open the battery cover and press the F/C button.  This will change the 

temperature display on the sensor only. 

 

On your station enter th

program menu

 to select Fahrenheit or Celsius temperature display 

on the station. 

 

WHY ARE MY WIND CUPS NOT SPINNING? 

 

 

Check for debris or ice preventing cups from moving. 

 

Check mounting location. Look for obstructions that prevent the wind from reaching the 

sensor.  

 

In most cases, the wind sensor needs to be 4-6ft above the highest point on the roof in 

order to clear nearby obstructions and read accurately.  

 

A 50-foot clearance in all directions is best.  

 

Push down firmly on the center of the cups to reseat them.  

 

Cups are replaceable. 

CAN I REPLACE MY WIND CUPS? 

 

Occasionally, a bad storm with hail or debris that will damage your wind cups.  These are easily 

replaced. 

 

Replace wind cups: 

1.

 

Loosen the screw on side of cups 

Summary of Contents for CA80550






















Reviews: