L3 2100-1010-00 Component Maintenance Manual With Illustrated Parts List Download

Page: 300 / 334

COMPONENT MAINTENANCE MANUAL

AVIATION RECORDERS

FA2100CVR

Rev. 15 Page 913

Apr. 14/16

Special Tools and Test Equipment

23–70–04

Use or disclosure of information on this sheet is subject

to the restrictions on the cover page of this document.

4.0



PIN1

FA2100

PI OR CICC

OR CICC/2

INTERFACE

AMP

748640-1

AMP

748747-1

GSS_PWR

TDM_CLK_HI

39VDC_RTN

TDM_CLK_LO

TDM_FRM_HI

TDM_FRM_LO

TDM_ADD_HI

TDM_ADD_LO

GND

SER_FS_AP_HI

SER_FS_AP_LO

PRGM_VPP_SW

PRGM_REC_L

SER_CLK_HI

SER_CLK_LO

SER_DAT_AP_HI

SER_DAT_AP_LO

TDM_DAT_HI

TDM_DAT_LO

SER_DAT_PI_HI

SER_DAT_PI_LO

SEL_SMP/FDP

SER_FS_PI_HI

SER_FS_PI_LO

TEST_MODE_L

GSE_PORT_EN

Figure 906.

Programmers Adapter Cable Assembly P/N: 17TES0058

The document reference is online, please check the correspondence between the online documentation and the printed version.

Summary of Contents for 2100-1010-00















































































































































































































































































































































Search results

Summary of Contents for 2100-1010-00

Reviews:

Related manuals for 2100-1010-00

Brands by name

Popular brands

L3 2100-1010-00, Component Maintenance Manual With Illustrated Parts List

Search results

Summary of Contents for 2100-1010-00

Reviews:

Related manuals for 2100-1010-00

Brands by name

Popular brands