L3 2100-1010-00 Component Maintenance Manual With Illustrated Parts List Download | Manualshive

Page: 263 / 334

background image

COMPONENT MAINTENANCE MANUAL

AVIATION RECORDERS

FA2100CVR

Rev. 15 Page 706

Apr. 14/16

Assembly

23–70–04

Use or disclosure of information on this sheet is subject

to the restrictions on the cover page of this document.

capacitor (1

−

130) to the top of the rear panel assembly using the support ca-

pacitor bracket (1

−

141).

(14) Connect the red blade connector (39 Vdc Hot) to the top, J4, connector on the

front side of the Aircraft Interface PWA.

(15) Connect the black blade connector (39 Vdc Return) to the lower, J5, connector

on the front side of the Aircraft Interface PWA.

D.

Audio Compressor PWA (AC) Installation
(See Figure 703 or IPL Figure 1, Item 155)

The Model FA2100’s Audio Compressor PWA is mounted to the Aircraft Interface
PWA located in the rear panel assembly of the recorder chassis. It provides digital
conversion and compression of the input audio stream. It interfaces to the Acquisi-
tion Processor PWA via interconnect cable assembly W003 through the J2 connec-
tor; and to the Aircraft Interface PWA via cable assembly W002 through the J1 con-
nector.

(1)

Ensure that the Aircraft Interface PWA (1-105) is installed into rear panel assembly
(1-90) as described in paragraph C. above.

(2)

Lay the rear panel assembly on its back with the Aircraft Interface PWA facing up.

(3)

Place the Assembly Support Tool fixture, Table 701: item 5, between the Aircraft
Interface PWA (1-105) and the rear panel assembly (1-90). Position the fixture
such that the inner part of the “U” shape is around the J1A connector.

NOTE:

This fixture is used to support the Aircraft Interface PWA
and prevent damage to the circuit board when installing the
two bottom standoff screws that attach to the Audio Com-
pressor PWA.

(4)

Secure Audio Compressor PWA (1-155) to the Aircraft Interface PWA standoffs
(1-120) using (4) pan-head screws (1-160) coated with adhesive Table 701: item 1.
Only hand tighten right now.

(5)

Tighten the (4) pan-head screws in a cross pattern and torque to a value of 5-6
in./lbs.

(6)

Remove the Assembly Support Tool fixture, Table 701: item 5 from under the Air-
craft Interface PWA.

(7)

Attach W002 (1

−

170) from the Aircraft Interface PWA to J1 on the Audio Compres-

sor PWA.

(8)

Attach W003 (1

−

165) to J2 on the Audio Compressor PWA.

The document reference is online, please check the correspondence between the online documentation and the printed version.

«
...
261
262
263
264
265
...
»

Summary of Contents for 2100-1010-00















































































































































































































































































































































Reviews:

No comments

Related manuals for 2100-1010-00

Brand: Datavideo Pages: 50

Brand: Coby Pages: 48

Brand: Sony Pages: 8

Brand: Pioneer Pages: 2

Brand: Pioneer Pages: 2

Brand: Pioneer Pages: 2

Brand: Pioneer Pages: 3

Brand: Pioneer Pages: 8

Brand: Pioneer Pages: 2

Brand: Pioneer Pages: 2

Brand: Pioneer Pages: 12

Brand: Pioneer Pages: 116

Brand: Pioneer Pages: 116

Brand: Pioneer Pages: 140

Brand: Pioneer Pages: 124

Brand: Pioneer Pages: 128

Brand: Pioneer Pages: 128

Brand: Pioneer Pages: 128

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands