L3 Communications Narda 8950/10 Operation And Installation Manual Download Page 15 | Manualshive

Page: 15 / 15

L3 Communications Narda 8950/10 Operation And Installation Manual Download Page 15

L-3 Communications, Narda Safety Test Solutions

Page 15

Narda 8950/10 Stray Voltage Detector

Narda Warranty

Narda Safety Test Solutions (Narda STS) warrants each product to be free from
any defect in material and workmanship for a period of two years after delivery
to, and return by the original purchaser. All warranty returns, however, must
first be authorized by a factory office representative.

The limit of liability under this warranty shall be to repair or replace any
product, or part thereof, which proves to be defective after inspection by
Narda STS. This warranty shall not apply to any Narda STS product that has
been disassembled, modified, physically or electrically damaged or any
product that has been subjected to conditions exceeding the applicable
specifications or ratings.

Narda STS shall not be liable for any direct or consequential injury, loss or
damage incurred through the use, or the inability to use, any Narda STS
product.

Narda STS reserves the right to make design changes to any Narda STS
product without incurring any obligation to make the same changes to
previously purchased units.

This warranty is the full extent of obligation and liability assumed by Narda
STS with respect to any and all Narda STS products. Narda STS neither makes,
nor authorizes any person to make, and other guarantee or warranty
concerning Narda STS products.

IPR2014-00839

Exhibit 2178

Page 15 of 15

«
...
13
14
15

Summary of Contents for Narda 8950/10
















Reviews:

No comments