background image

Available in either

L.P. Gas Vapor

Withdrawal or

Natural Gas

Configurations.

MODELS

OUTPUT 

(Btuh)

FUEL

HW220

220,000

Congratulations!

You have purchased the finest agricultural building heater available. 

Your new L.B. White heater incorporates the benefits from the most experienced
manufacturer of heating products using state-of-the-art technology.

We, at L.B. White, 

thank you

for your confidence in our products and 

welcome any suggestions or comments you may have...call us, toll-free, 
at (800) 345-7200.

Owner's Manual and Instructions

Therma Grow

Greenhouse Heaters

View this manual online at www.lbwhite.com

150-27595 REV.B

ATTENTION ALL USERS

This heater has been tested and evaluated by C.S.A. International, in
accordance with CSA International Requirement 1.95 U.S.- Greenhouse
Heaters for use as a direct gas-fired circulating heater for the heating of
greenhouses.  If you are considering using this product for any application
other than its intended use, then please contact your fuel gas supplier, or the
L.B. White Co., Inc.

SCAN THIS QR CODE

with your smartphone or 
visit http://goo.gl/ny7ua to
view maintenance videos
for L.B.White heaters.*

*Requires an app like QR Droid for Android or 
QR Reader for iPhone.

Summary of Contents for Therma Grow 120NG































Reviews: