L-Acoustics K Series Owner'S Manual Download

Page: 11 / 120

System components

BPCHAIN 1.5T

Extension sling 1.5 tons (included in K3-BUMP)

LA-SLING2T

Lifting chain (DIN EN 818-4) 2-leg , 8 mm

DELTA 1.5T

Azimuth angle tuning accessory 1.5T

K2-JACK

4 tilt adjustment screw jacks + bar for K2-CHARIOT

Transportation accessories

K3-CHARIOT

Chariot for up to 4 K3

K3-CHARIOTCOV

Protective cover for 4 K3 on K3-CHARIOT

K3-CHARIOTLID

Protective lid for K3-CHARIOT

K3-BUMPFLIGHT

Modular ightcase for 1 K3-BUMP and rigging elements

Software applications

Soundvision

3D acoustical and mechanical modeling software

LA Network Manager Software for remote control and monitoring of amplied controllers

Refer to the

Soundvision

help.

Refer to the

LA Network Manager

help.

Loudspeaker cables

0.7 m / 5 m / 10 m / 25 m

CH(1)

CH(2)

1 m

SP.7 / SP5 / SP10 / SP25

SP-Y1

0.7 m / 10 m / 25 m

SPK1
SPK2

SPK3
SPK4

5 m

DO.7 / DO10 / DO25

DOSUB-LA8

K3 owner's manual (EN) version 1.0

Summary of Contents for K Series

























































































































Search results

Summary of Contents for K Series

Reviews:

Related manuals for K Series

Brands by name

Popular brands

L-Acoustics K Series, Owner'S Manual

Search results

Summary of Contents for K Series

Reviews:

Related manuals for K Series

Brands by name

Popular brands