L-Acoustics K Series Owner'S Manual Download

Page: 10 / 120

System components

System components

Loudspeaker enclosures

2-way active WST

enclosure: 2 x 12" LF + 4" HF diaphragm

KS28

Flyable subwoofer 2 x 18''

KS21

High power compact subwoofer: 1x21''

Kara II

2-way active WST

enclosure: 2 x 8" LF + 3" HF diaphragm

Powering and driving system

LA4X / LA8 / LA12X

Amplied controller with DSP, preset library and networking capabilities

LA-RAK II AVB

Touring rack containing three LA12X, LA-POWER II for power distribution, LA-PANEL II for audio

and network distribution, and two LS10 for AVB distribution

Refer to the LA4X / LA8 / LA12X owner's manual for operating instructions.

Loudspeaker cables

SP cables

4-point speakON loudspeaker cables (4 mm² gauge)
SP cables come in four sizes: SP.7 (0.7 m/2.3 ft), SP5 (5 m/16.4 ft), SP10 (10 m/32.8 ft) and

SP25 (25 m/82 ft)

SP-Y1

breakout cable for two passive enclosures (2.5 mm² gauge) provided with a CC4FP adapter
4-point speakON to 2 × 2-point speakON

8-point PA-COM loudspeaker cables (4 mm² gauge)
DO cables come in three sizes: DO.7 (0.7 m/2.3 ft), DO10 (10 m/32.8 ft) and DO25

(25 m/82 ft)

DOSUB-LA8

breakout cable for four passive enclosures (4 mm² gauge)
8-point PA-COM to 4 × 2-point speakON

DOFILL-LA8

breakout cable for two 2-way active enclosures (4 mm² gauge)
8-point PA-COM to 2 x 4-point speakON

DO3WFILL

breakout cable for one 2-way active enclosure and two passive enclosures (4 mm² gauge)
8-point PA-COM to 1 x 4-point speakON and 2 x 2-point speakON

Information about the connection of the enclosures to the LA amplied controllers is given in

this document.

Refer to the LA4X / LA8 / LA12X owner's manual for detailed instructions about the whole cabling scheme,

including modulation cables and network.

Rigging elements

K3-BUMP

Flying frame for K3

K3-BAR

Extension bar for K3-BUMP

K3-RIGBAR

Rigging bar and pullback for K3 (includes LA-SLING2T)

KARADOWNK3

Interface for ying Kara below K3

LA-RAKMOUNT

Mounting cradles for LA-RAK

K3-TILT

Rigging element for stacking K3 on KS28

KS28-OUTRIG

Stability bars for KS28

K3 owner's manual (EN) version 1.0

Summary of Contents for K Series

























































































































Search results

Summary of Contents for K Series

Reviews:

Related manuals for K Series

Brands by name

Popular brands

L-Acoustics K Series, Owner'S Manual

Search results

Summary of Contents for K Series

Reviews:

Related manuals for K Series

Brands by name

Popular brands