Kyocera KM-2560 Service Manual Download Page 67 | Manualshive

Page: 67 / 392

Kyocera KM-2560 Service Manual Download Page 67

2H0/2HZ-1

1-3-31

U070

Adjusting the DP magnification
Description

Adjusts the DP original scanning speed.

Purpose

Make the adjustment if the magnification is incorrect in the auxiliary scanning direction when the optional DP
is used.

Method

1. Press the start key.
2. Select the item to be adjusted.

Adjustment

1. Press the system menu key.
2. Place an original on the DP and press the start key to make a test copy.
3. Press the system menu key.
4. Change the setting value using the +/- or numeric keys.

For copy example 1, increase the value. For copy example 2, decrease the value.

Figure 1-3-13

5. Press the start key. The value is set.

Caution

Check the copy image after the adjustment. If the image is still incorrect, perform the following adjustments in
maintenance mode.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Display

Description

Setting
range

Initial
setting

Change in
value per step

MAIN ADJ

Magnification in the auxiliary scanning
direction (first page)

-25 to 25

0

0.1 %

SUB ADJ

Magnification in the auxiliary scanning
direction (second page)

-25 to 25

0

0.1 %

Original

Copy

example 1

Copy

example 2

U070

U071

U404

«
...
65
66
67
68
69
...
»

Summary of Contents for KM-2560









































































































































































































































































































































































































Reviews:

No comments