Kyocera Copystar CS-1635 Service Manual Download Page 77

Page: 77 / 244

2HA/2HB

1-3-45

U402

Adjusting margins of image printing
Description

Adjusts margins for image printing.

Purpose

Make the adjustment if margins are incorrect.

Adjustment

1. Press the start key.
2. Select the item using the exposure adjustment keys.

3. Press the interrupt key.
4. Press the start key to output a test pattern.
5. Change the setting value using the zoom +/- keys.

Increasing the value makes the margin wider, and decreasing it makes the margin narrower.

Figure 1-3-15

6. Press the start key. The value is set.

Caution

Check the copy image after the adjustment. If the image is still incorrect, perform the following adjustments in
maintenance mode.

Completion

Press the stop/clear key. The indication for selecting a maintenance item No. appears.

Maintenance

item No.

Description

Exposure
indicator

Description

Setting
range

Initial
setting

Change in
value per step

Exp. 1

Printer leading edge margin

0.0 to 10.0

3.0

0.5 mm

Exp. 2

Printer left/right margins

-3.4 to 10.0

3.0

0.5 mm

Exp. 3

Printer trailing edge margin

-5.0 to 10.0

4.0

0.5 mm

Ejection direction

(reference)

Printer leading edge margin
(3 ± 2.5 mm)

Printer

left margin

(2.5

+1.5

mm)

Printer
right margin
(2.5

+1.5

mm)

Printer trailing edge margin
(3 ± 2.5 mm)

–2.0

U402

U403

(P.1-3-46)

U404

(P.1-3-47)

Summary of Contents for Copystar CS-1635





















































































































































































































































Search results

Summary of Contents for Copystar CS-1635

Reviews:

Related manuals for Copystar CS-1635

Brands by name

Popular brands

Kyocera Copystar CS-1635, Service Manual

Search results

Summary of Contents for Copystar CS-1635

Reviews:

Related manuals for Copystar CS-1635

Brands by name

Popular brands