Kyocera Copystar CS-1635 Service Manual Download Page 51

Page: 51 / 244

2HA/2HB

1-3-19

U066

Adjusting the scanner leading edge registration
Description

Adjusts the scanner leading edge registration of the original scanning.

Purpose

Make the adjustment if there is a regular error between the leading edges of the copy image and original.

Caution

Before making this adjustment, ensure that the following adjustments have been made in maintenance mode

Adjustment

1. Press the start key.

2. Press the interrupt key.
3. Place an original and press the start key to make a test copy.
4. Change the setting value using the zoom +/- keys.

For copy example 1, decrease the value. For copy example 2, increase the value.

Figure 1-3-8

5. Press the start key. The value is set.

Completion

Press the stop/clear key. The indication for selecting a maintenance item No. appears.

Maintenance

item No.

Description

U066

U034

(P.1-3-12)

U071

(P.1-3-22)

Description

Setting range

Initial setting

Scanner leading edge registration

-32 to 20

Original

Copy

example 1

Copy

example 2

Scanner leading edge registration

Summary of Contents for Copystar CS-1635





















































































































































































































































Search results

Summary of Contents for Copystar CS-1635

Reviews:

Related manuals for Copystar CS-1635

Brands by name

Popular brands

Kyocera Copystar CS-1635, Service Manual

Search results

Summary of Contents for Copystar CS-1635

Reviews:

Related manuals for Copystar CS-1635

Brands by name

Popular brands